Toyota Tacoma (2015-2018) Service Manual: Automatic Transmission System(for 2gr-fks)
- Definition Of Terms
- Parts Location
- Precaution
- How To Proceed With Troubleshooting
- System Description
- System Diagram
- Hydraulic Test
- Mechanical System Tests
- Road Test
- Initialization
- Manual Shifting Test
- Monitor Drive Pattern
- Problem Symptoms Table
- Terminals Of Ecm
- Check Mode Procedure
- Diagnosis System
- Dtc Check / Clear
- Fail-safe Chart
- Data List / Active Test
- Diagnostic Trouble Code Chart
- System Voltage Circuit Short to Ground or Open (P056014)
- Starter Relay Circuit Short to Battery (P061512)
- Vehicle Control History
- Brake Switch "B" Circuit Short to Battery (P070312)
- Transmission Fluid Temperature Sensor "A" Circuit Short To Ground (P071011)
- Torque Converter Clutch Circuit Short to Ground (P074011)
- Torque Converter Clutch Circuit Short to Battery or Open (P074015)
- Transmission Fluid Temperature Sensor "B" Circuit Short to Ground (P274011)
- Transmission Fluid Temperature Sensor "B" Circuit Short to Battery or Open (P274015)
- Lost Communication with ECM/PCM "A" Missing Message (U010087)
- Internal Control Module EEPROM Data Memory Failure (P062F44)
- Pressure Control Solenoid "G" Actuator Stuck Off (P28077F)
- Vehicle Speed Sensor "A" No Signal (P050031)
- Transmission Range Sensor "A" Circuit Open (P070513,P070562)
- Pressure Control Solenoid "G" Circuit Open (P280713)
- Input/Turbine Speed Sensor "A" Circuit Short to Battery (P071512,P071514,P071531)
- Output Speed Sensor Circuit Short to Battery (P072012,P072014,P072031)
- Pressure Control Solenoid "A" Circuit Open (P074513)
- Pressure Control Solenoid "B" Actuator Stuck Off (P07757F)
- Pressure Control Solenoid "B" Circuit Open (P077513)
- Pressure Control Solenoid "C" Actuator Stuck Off (P07957F)
- Pressure Control Solenoid "C" Circuit Open (P079513)
- Pressure Control Solenoid "D" Circuit Open (P271313)
- Pressure Control Solenoid "A" Actuator Stuck Off (P07457F)
- Transmission Fluid Temperature Sensor "A" Circuit Range/Performance (P071000)
- Torque Converter Clutch Pressure Control Solenoid Control Circuit Open (P275613)
- Pattern Select Switch Power Mode Circuit
Adjustment
ADJUSTMENT
PROCEDURE
1. BEFORE FILLING TRANSMISSION
The AC60E automatic transmission assembly requires Toyota Genuine ATF
WS.
If the entire automatic transmission assembly, automatic ...
Definition Of Terms
DEFINITION OF TERMS
Term
Definition
Monitor description
Description of what the ECM monitors and how it detects malfunctions
(monitoring purpose ...
Other materials:
Parts Location
PARTS LOCATION
ILLUSTRATION
*A
for Hydraulic Brake Booster
*B
for Vacuum Brake Booster
*C
for Automatic Transmission
*D
for Manual Transmission
*1
SKID CONTROL ECU (BRAKE ACT ...
Radio Antenna
Components
COMPONENTS
ILLUSTRATION
Removal
REMOVAL
PROCEDURE
1. REMOVE ROOF HEADLINING ASSEMBLY (for Double Cab)
(See page )
2. REMOVE ROOF HEADLINING ASSEMBLY (for Access Cab)
(See page )
3. REMOVE ANTENNA ASSEMBLY WITH HOLDER
(a) Disengage the 3 clamps.
(b) Remove the nut.
...
Blind Spot Monitor Master Module Beam Axis Inspection Incomplete (C1ABB)
DESCRIPTION
This DTC is stored when a beam axis inspection has not been performed for the
blind spot monitor sensor LH.
HINT:
This DTC is always stored after replacing a blind spot monitor sensor. The purpose
of this DTC is to ensure that beam axis inspection is performed. Completing the
be ...
