Toyota Tacoma (2015-2018) Service Manual: Brake Switch "B" Circuit Short to Battery (P070312)

Toyota Tacoma (2015-2018) Service Manual / Ac60e Automatic Transmission / Transaxle / Automatic Transmission System(for 2gr-fks) / Brake Switch "B" Circuit Short to Battery (P070312)

DESCRIPTION

The purpose of this circuit is to prevent the engine from stalling while driving in lock-up when the brakes are suddenly applied.

When the brake pedal is depressed, this switch sends a signal to the ECM. Then the ECM cancels the operation of the lock-up clutch while braking is in progress.

DTC Code	DTC Detection Condition	Trouble Area	SAE
P070312	Stop light switch remains on even when the vehicle is driven in a stop (less than 3 km/h (1.86 mph)) and go (30 km/h (18.65 mph) or more) pattern 5 times (2 trip detection logic).	Short in stop light switch signal circuit Stop light switch ECM	P0724

MONITOR DESCRIPTION

This DTC indicates that the stop light switch remains on. When the stop light switch remains on during stop and go driving, the ECM interprets this as a fault in the stop light switch. Then the MIL illuminates and the ECM stores the DTC. The vehicle must stop (less than 3 km/h (1.86 mph)) and go (30 km/h (18.65 mph) or more) 5 times for 2 driving cycles in order for the DTC to be stored.

MONITOR STRATEGY

Related DTCs	P0724: Stop light switch/Verify switch input
Required sensors/Components	Stop light switch
Frequency of operation	Continuous
Duration	GO and STOP 5 times
MIL operation	2 driving cycles
Sequence of operation	None

TYPICAL ENABLING CONDITIONS

The stop light switch remains on during GO and STOP 5 times.

GO and STOP are defined as follows:

The monitor will run whenever the following DTCs are not stored	None
Battery voltage	8 V or higher
Ignition switch	ON
Starter	OFF
GO: Vehicle speed	30 km/h (18.65 mph) or more
STOP: Vehicle speed	Less than 3 km/h (1.86 mph)

TYPICAL MALFUNCTION THRESHOLDS

Stop light switch

CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
When clearing the permanent DTCs, refer to the Clear Permanent DTC procedure (See page ).

Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for 2 minutes or more.
Turn the ignition switch to ON and turn the Techstream on.
Start the engine.
Repeat the following procedure 5 times [*1]:
- Accelerate the vehicle to 30 km/h (18.65 mph) or more, depress the brake pedal and decelerate the vehicle to 3 km/h (1.86 mph) or less.
  HINT:
  
  [*1] : Normal judgment procedure.
  
  The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
Stop the vehicle.
Enter the following menus: Powertrain / Transmission / Utility / All Readiness.
Input the DTC: P070312.

Check the DTC judgment result.

Techstream Display	Description
NORMAL	DTC judgment completed System normal
ABNORMAL	DTC judgment completed System abnormal
INCOMPLETE	DTC judgment not completed Perform driving pattern after confirming DTC enabling conditions
N/A	Unable to perform DTC judgment Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

HINT:

If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the normal judgment procedure again.

WIRING DIAGRAM

Refer to SFI system DTC P05042B (See page CAUTION / NOTICE / HINT ).

CAUTION / NOTICE / HINT

NOTICE:

Perform the universal trip to clear permanent DTCs (See page ).
Perform registration and/or initialization when parts related to the automatic transmission are replaced (See page ).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1. DATA LIST

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

(a) Warm up the engine.

(b) Turn the ignition switch off.

(d) Turn the ignition switch to ON.

(e) Turn the Techstream on.

(f) Enter the following menus: Powertrain / Transmission / Data List.

(g) According to the display on the Techstream, read the Data List.

Transmission

Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
Stop Light SW	Stop light switch status/ ON or OFF	ON: Brake pedal depressed OFF: Brake pedal released	-

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

Stop Light SW

Stop light switch status/

ON or OFF

ON: Brake pedal depressed
OFF: Brake pedal released

PROCEDURE

1.	READ VALUE USING TECHSTREAM (STOP LIGHT SWITCH)

(a) Connect the Techstream to the DLC3.

(b) Turn the Ignition switch ON.

(d) Enter the following menus: Powertrain / Transmission / Data List.

(e) According to the display on the Techstream, read the Data List.

Transmission

Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
Stop Light Switch	Stop light switch status/ ON or OFF	ON: Brake pedal depressed OFF: Brake pedal released	-

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

Stop Light Switch

Stop light switch status/

ON or OFF

ON: Brake pedal depressed
OFF: Brake pedal released

Result:

Result	Proceed to
Data List value is normal	A
Data List value is not normal	B

CHECK FOR INTERMITTENT PROBLEMS

2.	CHECK STOP LIGHT SWITCH ASSEMBLY INSTALLATION

(a) Check the stop light switch assembly installation (See page OK: ).

OK:

Stop light switch is installed correctly.

SECURELY REINSTALL STOP LIGHT SWITCH ASSEMBLY

3.	CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)

(a) Disconnect the S10 stop light switch assembly connector.

(b) Disconnect the E13 ECM connector.

Standard Resistance:

Tester Connection	Condition	Specified Condition
S10-1 or E13-16 (STP) - Other terminals	Always	10 kΩ or higher

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.	CHECK STOP LIGHT SWITCH ASSEMBLY

(a) Check the stop light switch assembly (See page ).

REPLACE ECM

REPLACE STOP LIGHT SWITCH ASSEMBLY

Vehicle Control History

VEHICLE CONTROL HISTORY VEHICLE CONTROL HISTORY (a) A part of the control history can be confirmed using the vehicle control history. Click here ...

Transmission Fluid Temperature Sensor "A" Circuit Short To Ground (P071011)

DESCRIPTION The No. 1 ATF temperature sensor converts the fluid temperature into a resistance value for use by the ECM. The ECM applies a voltage to the temperature sensor through terminal THO1 of ...

Other materials:

Front Occupant Classification Sensor RH Collision Detection (B1786)
DESCRIPTION DTC B1786 is set when the occupant detection ECU receives a collision detection signal, which is sent by the front occupant classification sensor RH when an accident occurs. DTC B1786 is also set when the front seat with adjuster frame assembly RH is subjected to a strong impact, ...

Removal
REMOVAL PROCEDURE 1. REMOVE FRONT CONSOLE BOX (See page ) 2. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (a) Move the shift lever to N. (b) Disconnect the end of the transmission control cable assembly from the transmission floor shift assembly. Text in Illustration ...

Power Source Circuit
DESCRIPTION This circuit provides power to operate the forward recognition camera. WIRING DIAGRAM CAUTION / NOTICE / HINT NOTICE: Inspect the fuses for circuits related to this system before performing the following inspection procedure. PROCEDURE 1. CHECK HARNESS A ...