Toyota Tacoma (2015-2018) Service Manual: Air Conditioning
- Air Conditioning Amplifier
- Air Conditioning Panel(for Automatic Air Conditioning System)
- Air Conditioning Panel(for Manual Air Conditioning System)
- Air Conditioning Pressure Sensor
- Air Conditioning System(for Automatic Air Conditioning System)
- Parts Location
- Precaution
- System Diagram
- Customize Parameters
- How To Proceed With Troubleshooting
- System Description
- Diagnosis System
- Problem Symptoms Table
- Terminals Of Ecu
- Data List / Active Test
- Diagnostic Trouble Code Chart
- Dtc Check / Clear
- Lost Communication with Front Panel LIN (B14B2)
- Air Mix Damper Control Servo Motor Circuit (Driver Side) (B1446/46)
- Air Mix Damper Position Sensor Circuit (Passenger Side) (B1431/31)
- Air Inlet Damper Position Sensor Circuit (B1432/32)
- Lost Communication with ECM (U0100,U0142,U0155)
- Air Outlet Damper Control Servo Motor Circuit (B1443/43)
- Air Outlet Damper Position Sensor Circuit (B1433/33)
- Air Mix Damper Position Sensor Circuit (Driver Side) (B1436/36)
- Air Inlet Damper Control Servo Motor Circuit (B1442/42)
- Room Temperature Sensor Circuit (B1411/11)
- Air Mix Damper Control Servo Motor Circuit (Passenger Side) (B1441/41)
- Ambient Temperature Sensor Circuit (B1412/12)
- Evaporator Temperature Sensor Circuit (B1413/13)
- Compressor Lock Sensor Circuit (B1422/22)
- Air Conditioning Compressor Magnetic Clutch Circuit
- Pressure Sensor Circuit (B1423/23)
- Blower Motor Circuit
- IG Power Source Circuit
- PTC Heater Circuit
- Back-up Power Source Circuit
- Air Conditioning System(for Manual Air Conditioning System)
- Parts Location
- Precaution
- How To Proceed With Troubleshooting
- System Description
- System Diagram
- Problem Symptoms Table
- Diagnosis System
- Dtc Check / Clear
- Terminals Of Ecu
- Data List / Active Test
- Diagnostic Trouble Code Chart
- Ambient Temperature Sensor Circuit (B1412)
- Pressure Sensor Circuit (B1423)
- Lost Communication with ECM (U0100,U0142,U0155)
- Air Conditioning Compressor Magnetic Clutch Circuit
- Evaporator Temperature Sensor Circuit (B1413)
- Compressor Lock Sensor Circuit (B1422)
- PTC Heater Circuit
- Air Conditioning Unit
- Air Inlet Control Servo Motor
- Air Mix Control Servo Motor
- Air Outlet Control Servo Motor
- Ambient Temperature Sensor
- Blower Motor Controller
- Compressor
- Condenser
- Front Blower Motor
- Front Blower Resistor
- Front Evaporator Temperature Sensor
- Heater Relay
- Magnetic Clutch Relay
- Ptc Heater Assembly
- Ptc Heater Relay
- Refrigerant Line
- Refrigerant(for Hfc-134a(r134a))
- Refrigerant(for Hfo-1234yf(r1234yf))
- Room Temperature Sensor
Repair
REPAIR
PROCEDURE
1. STEERING OFF CENTER REPAIR PROCEDURE
(a) Check if the steering wheel is off center.
(1) Apply masking tape to the top center of the steering wheel and upper
stee ...
Air Conditioning Amplifier
Components
COMPONENTS
ILLUSTRATION
Installation
INSTALLATION
PROCEDURE
1. INSTALL AIR CONDITIONING AMPLIFIER ASSEMBLY
(a) Install the air conditioner amplifier assembly with the 2 bolts.
...
Other materials:
Short to +B in Outer Mirror Indicator(Slave) (C1AB1)
DESCRIPTION
This DTC is stored when the blind spot monitor sensor RH detects a +B short in
the blind spot monitor indicator RH.
DTC Code
DTC Detection Condition
Trouble Area
C1AB1
With the blind spot monitor main switch assembly (warni ...
Blind Spot Monitor Slave Module Beam Axis Inspection Incomplete (C1ABC)
DESCRIPTION
This DTC is stored when a beam axis inspection has not been performed for the
blind spot monitor sensor RH.
HINT:
This DTC is always stored after replacing a blind spot monitor sensor. The purpose
of this DTC is to ensure that beam axis inspection is performed. Completing the
be ...
Event data recorder
This vehicle is equipped with an event data recorder (EDR). The main purpose
of an EDR is to record, in certain crash or near crash-like situations, such as
an air bag deployment or hitting a road obstacle, data that will assist in understanding
how a vehicle’s systems performed. The EDR is ...
