Toyota Tacoma (2015-2018) Service Manual: Customize Parameters
CUSTOMIZE PARAMETERS
NOTICE:
- When the customer requests a change in a function, first make sure that the function can be customized.
- Make a note of the current settings before customizing.
HINT:
The following PCS functions and the pre-collision system sensitivity setting can be changed from their default setting.
CUSTOMIZE PRE-COLLISION SYSTEM
(a) Customizing with the Techstream
(1) Turn the ignition switch off.
(2) Connect the Techstream to the DLC3.
(3) Turn the ignition switch to ON.
(4) Turn the Techstream on.
(5) Enter the following menus: Customize Setting / Others.
(6) Select the setting by referring to the table below.
Others|
Tester Display |
Description |
Default |
Setting |
ECU |
|---|---|---|---|---|
|
PCS Operation State Retention Setting |
Refer to the table below |
OFF |
0:OFF,1:ON |
Millimeter wave radar sensor assembly |
|
PCS Alarm Activation Distance Retention Setting 1 |
Refer to the table below |
OFF |
0:OFF,1:ON |
Millimeter wave radar sensor assembly |
|
PCS Alarm Activation Distance Retention Setting 2 |
Refer to the table below |
ON |
0:OFF,1:ON |
Millimeter wave radar sensor assembly |
|
PCS Alarm Activation Distance Retention Setting 3 |
Refer to the table below |
OFF |
0:OFF,1:ON |
Millimeter wave radar sensor assembly |
|
Customize Setting |
Description |
Setting |
|---|---|---|
|
PCS Operation State Retention Setting |
Function to maintain the pre-collision system on/off setting when the ignition switch is turned off and then to ON. |
OFF: Not maintained (Pre-collision system always turns on) ON: Maintained |
|
PCS Alarm Activation Distance Retention Setting 1 |
Function to maintain the sensitivity setting of the pre-collision system when the pre-collision system is turned off and then on. |
OFF: Not maintained (Setting changes to "Mid") ON: Maintained |
|
PCS Alarm Activation Distance Retention Setting 2 |
Function to maintain the sensitivity setting of the pre-collision system when the ignition switch is turned off while the pre-collision system is on. |
OFF: Not maintained (Setting changes to "Mid") ON: Maintained |
|
PCS Alarm Activation Distance Retention Setting 3 |
Function to maintain the sensitivity setting of the pre-collision system when the ignition switch is turned off while the pre-collision system is off. |
OFF: Not maintained (Setting changes to "Mid") ON: Maintained |
System Diagram
SYSTEM DIAGRAM
Communication Table
Sender
Receiver
Signal
Line
Millimeter Wave Radar Sensor Assembly
Forward Recognition Ca ...
How To Proceed With Troubleshooting
CAUTION / NOTICE / HINT
HINT:
Use the following procedure to troubleshoot the pre-collision system.
*: Use the Techstream.
PROCEDURE
1.
VEHICLE BROUGHT ...
Other materials:
GPS Mark is not Displayed
PROCEDURE
1.
CHECK CABIN
(a) Check the cabin for any object that might interrupt radio reception or additional
devices which use radio waves on the instrument panel. If such an object exists,
remove it and check if the GPS mark reappears.
HINT:
The GPS uses ex ...
Operation Check
OPERATION CHECK
1. CHECK INTERMITTENT CONTROL FUNCTION (w/ Intermittent Time Adjustment Switch)
(a) Turn the ignition switch to ON.
(b) Turn the windshield wiper switch assembly to the INT position.
(c) Check that the intermittent operation interval can be adjusted from approximately
1.6 to 10 ...
Wireless Charger Power Source Circuit
DESCRIPTION
This is the power source circuit to operate the mobile wireless charger cradle
assembly.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
Inspect the fuses for circuits related to this system before performing the following
inspection procedure.
PROCEDURE
1.
...
