Toyota Tacoma (2015-2018) Service Manual: Vehicle Speed Sensor Circuit (C1AA3)

Toyota Tacoma (2015-2018) Service Manual / Cruise Control / Forward Recognition Camera System / Vehicle Speed Sensor Circuit (C1AA3)

DESCRIPTION

The forward recognition camera receives vehicle speed signals from the skid control ECU. If the skid control ECU receives a vehicle speed sensor malfunction signal, it informs the forward recognition camera via CAN communication, and DTC C1AA3 is stored.

DTC No.	Detection Item	DTC Detection Condition	Trouble Area
C1AA3	Vehicle Speed Sensor Circuit	3 seconds after the ignition switch is turned to ON, a signal from the skid control ECU indicating a malfunction in a vehicle speed sensor is detected by the forward recognition camera for 5 seconds or more.	Vehicle stability control system Skid control ECU (brake actuator assembly)1 Skid control ECU (master cylinder solenoid)2 Forward recognition camera

*1: for Vacuum Brake Booster
*2: for Hydraulic Brake Booster

CAUTION / NOTICE / HINT

NOTICE:

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.
If the forward recognition camera has been replaced with a new one, be sure to perform Forward Recognition Camera Axis Adjustment.
Click here
The forward recognition camera system uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to How to Proceed with Troubleshooting.
Click here

PROCEDURE

1.	CHECK FOR DTCs (VEHICLE STABILITY CONTROL SYSTEM)

HINT:

If DTC C1AA3 is stored, the vehicle stability control system may be malfunctioning. Check for DTCs related to the vehicle stability control system first.

(a) Check for DTCs.

for Vacuum Brake Booster
Click here
for Hydraulic Brake Booster
Click here

Result	Proceed to
Vehicle stability control system DTCs are not output	A
Vehicle stability control system DTCs are output (for Vacuum Brake Booster)	B
Vehicle stability control system DTCs are output (for Hydraulic Brake Booster)	C

GO TO VEHICLE STABILITY CONTROL SYSTEM

2.	CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)

(a) Clear the DTCs.

Click here (b) Make sure that the DTC detection conditions are met.

(b) Make sure that the DTC detection conditions are met.

HINT:

If the conditions are not met, the system cannot detect the malfunction.

Click here

Result	Proceed to
DTC C1AA3 is not output	A
DTC C1AA3 is output	B

USE SIMULATION METHOD TO CHECK

3.	REPLACE FORWARD RECOGNITION CAMERA

(a) Replace the forward recognition camera.

Click here (b) Perform forward recognition camera axis adjustment.

(b) Perform forward recognition camera axis adjustment.

Click here

4.	CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)

(a) Clear the DTCs.

Click here (b) Make sure that the DTC detection conditions are met.

(b) Make sure that the DTC detection conditions are met.

HINT:

If the conditions are not met, the system cannot detect the malfunction.

Click here

Result	Proceed to
DTC C1AA3 is not output	A
DTC C1AA3 is output (for Vacuum Brake Booster)	B
DTC C1AA3 is output (for Hydraulic Brake Booster)	C

END (FORWARD RECOGNITION CAMERA WAS DEFECTIVE)

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

REPLACE SKID CONTROL ECU (MASTER CYLINDER SOLENOID)

FCM Destination Information Uninitialized (C1AAA)

DESCRIPTION When the forward recognition camera is replaced with a new one, the new forward recognition camera attempts to store the country specification information received from the main body ...

Skid Control Buzzer Circuit (C1AA7)

DESCRIPTION The forward recognition camera operates the pre-collision warning by sending a buzzer request signal to the skid control buzzer. If the forward recognition camera detects a malfunction ...

Other materials:

Antenna Coil Open / Short (B2784)
DESCRIPTION When an open or short circuit is detected in the antenna coil built into the transponder key coil, the transponder key ECU assembly stores this DTC. DTC No. DTC Detection Condition Trouble Area DTC Output Confirmation Operation ...

Installation
INSTALLATION PROCEDURE 1. INSTALL FRONT CRANKSHAFT OIL SEAL (a) Using SST and a hammer, tap in a new oil seal until its surface is flush with the timing chain cover assembly edge. SST: 09223-22010 SST: 09506-35010 NOTICE: Keep the lip free from foreign matt ...

Fuel Pressure Sensor
Components COMPONENTS ILLUSTRATION Inspection INSPECTION PROCEDURE 1. INSPECT FUEL DELIVERY PIPE SUB-ASSEMBLY (FUEL PRESSURE SENSOR) NOTICE: Do not remove the fuel pressure sensor from the fuel delivery pipe sub-assembly. If a fuel pressure sensor is removed, replace the ...