Toyota Tacoma (2015-2018) Service Manual: Installation

Toyota Tacoma (2015-2018) Service Manual / 2gr-fks Engine Mechanical / Engine Unit / Installation

INSTALLATION

PROCEDURE

1. INSTALL ENGINE COOLANT TEMPERATURE SENSOR

2. INSTALL ENGINE OIL PRESSURE SWITCH ASSEMBLY

3. INSTALL IGNITION COIL ASSEMBLY

4. INSTALL FUEL INJECTOR SEAL

5. INSTALL FUEL INJECTOR ASSEMBLY

6. INSTALL FUEL DELIVERY PIPE RH

7. INSTALL FUEL DELIVERY PIPE ASSEMBLY LH (FUEL PRESSURE SENSOR)

8. INSTALL NO. 2 FUEL PIPE SUB-ASSEMBLY

9. SET FUEL PUMP ASSEMBLY (for High Pressure)

10. TEMPORARILY INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY

11. INSTALL FUEL PUMP ASSEMBLY (for High Pressure)

12. INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY

13. INSTALL FUEL TUBE SUB-ASSEMBLY

14. INSTALL WIRE HARNESS CLAMP BRACKET

15. INSTALL INTAKE MANIFOLD

16. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY

17. INSTALL VACUUM PUMP ASSEMBLY (for Vacuum Brake Booster)

18. INSTALL VACUUM PUMP HOLE COVER BRACKET (for Hydraulic Brake Booster)

(a) Install a new O-ring.

(b) Apply engine oil to the O-ring.

Torque:

21 N·m {214 kgf·cm, 15 ft·lbf}

NOTICE:

Be careful not to pinch the O-ring.
After installation, check that there are no gaps between the matching surfaces and that the vacuum pump hole cover bracket is no installed at an angle.

19. CONNECT NO. 4 WATER BY-PASS HOSE (for Automatic Transmission)

(a) Connect the No. 4 water by-pass hose and slide the hose clip to secure it.

20. INSTALL NO. 2 WATER BY-PASS PIPE (for Automatic Transmission)

(a) Install the No. 2 water by-pass pipe with the 2 bolts.

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

(b) Connect the No. 10 water by-pass hose and slide the hose clip to secure it.

21. INSTALL NO. 2 WATER BY-PASS PIPE (for Manual Transmission)

(a) Install the No. 2 water by-pass pipe with the 2 bolts.

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

(b) Connect the No. 10 water by-pass hose and slide the 2 hose clips to secure it.

22. INSTALL WATER HOSE SUB-ASSEMBLY

(a) Install the water hose sub-assembly and slide the 2 hose clips to secure it.

23. INSTALL NO. 1 WATER BY-PASS PIPE (w/ Oil Cooler)

(a) Install the No. 1 water by-pass pipe with the 3 bolts and nut as shown in the illustration.

Text in Illustration

*a	Nut
*b	Bolt

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

(b) Connect the 4 hoses and slide the 4 hose clips to secure it.

24. INSTALL NO. 4 WATER BY-PASS HOSE

(a) Install the No. 4 water by-pass hose and slide the hose clip to secure it.

25. INSTALL NO. 3 WATER BY-PASS HOSE

(a) Install the No. 3 water by-pass hose and slide the 2 hose clips to secure it.

26. INSTALL NO. 2 WATER BY-PASS HOSE

(a) Install the No. 2 water by-pass hose and slide the 2 hose clips to secure it.

27. INSTALL WATER BY-PASS HOSE

(a) Install the water by-pass hose and slide the 2 hose clips to secure it.

28. INSTALL NO. 5 WATER BY-PASS HOSE

(a) Install the No. 5 water by-pass hose and slide the hose clip to secure it.

29. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

(a) Install the V-ribbed belt tensioner assembly with the 2 bolts.

Torque:

43 N·m {438 kgf·cm, 32 ft·lbf}

30. INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY

(a) Install the 2 No. 2 idler pulley sub-assemblies with the 2 bolts.

Torque:

43 N·m {438 kgf·cm, 32 ft·lbf}

31. INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY

(a) Install the No. 1 idler pulley sub-assembly with the bolt.

Text in Illustration

"DOUBLE"

Torque:

54 N·m {551 kgf·cm, 40 ft·lbf}

HINT:

"DOUBLE" is marked on the idler pulley to distinguish it from the No. 2 idler pulley.

32. INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET

(a) Install the No. 1 compressor mounting bracket with the 2 bolts.

Torque:

43 N·m {438 kgf·cm, 32 ft·lbf}

33. INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET LH

(a) Install the front No. 1 engine mounting bracket LH with the 3 bolts.

Torque:

43 N·m {438 kgf·cm, 32 ft·lbf}

34. INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET RH

(a) Install the front No. 1 engine mounting bracket RH with the 4 bolts.

Torque:

43 N·m {438 kgf·cm, 32 ft·lbf}

35. INSTALL OIL LEVEL DIPSTICK GUIDE

(a) Apply a light coat of the engine oil to a new O-ring.

(b) Install the O-ring.

NOTICE:

During installation, be careful not to damage the O-ring.

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

NOTICE:

Make sure that the O-ring is not damaged or does not jump out of position during installation.

(d) Connect the clamp.

36. INSTALL OIL LEVEL DIPSTICK SUB-ASSEMBLY

(a) Install the oil level dipstick sub-assembly.

Precaution

PRECAUTION HINT: Any digits beyond the 0.01 mm (1/1000 in.) place for standard, minimum and maximum values should be used as a reference only. When both standard and maximum or minim ...

Front Crankshaft Oil Seal

Components COMPONENTS ILLUSTRATION Installation INSTALLATION PROCEDURE 1. INSTALL TIMING GEAR CASE OR TIMING CHAIN CASE OIL SEAL (a) Apply MP grease to the lip of a new timing gear case o ...

Other materials:

Stereo Component Amplifier Disconnected (B15D3)
DESCRIPTION The navigation receiver assembly and stereo component amplifier assembly are connected by the AVC-LAN communication line. When an AVC-LAN communication error occurs between the navigation receiver assembly and stereo component amplifier assembly, this DTC will be stored. ...

Removal
REMOVAL CAUTION / NOTICE / HINT HINT: Use the same procedure for both the RH and LH sides. The procedure described below is for the LH side. PROCEDURE 1. PRECAUTION NOTICE: After turning the ignition switch off, waiting time may be required before disconnecting the cable f ...

Heater Circuit (C1AAE)
DESCRIPTION If the forward recognition camera detects a malfunction in the camera heater (forward recognition hood) circuit, it will output a malfunction signal to the millimeter wave radar sensor assembly via CAN communication and DTC C1AAE will be stored. DTC No. Detect ...