Toyota Tacoma manuals

Toyota Tacoma (2015-2018) Service Manual: Removal

REMOVAL

CAUTION / NOTICE / HINT

HINT:

  • Use the same procedure for both the RH and LH sides.
  • The procedure described below is for the LH side.

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here 3. REMOVE FRONT DOOR SCUFF PLATE

3. REMOVE FRONT DOOR SCUFF PLATE

Click here 4. REMOVE REAR DOOR SCUFF PLATE

4. REMOVE REAR DOOR SCUFF PLATE

Click here 5. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP

5. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP

(a) Disconnect the front door opening trim weatherstrip to the extent which allows the removal of the center pillar lower garnish and center pillar upper garnish.

6. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

(a) Disconnect the rear door opening trim weatherstrip to the extent which allows the removal of the center pillar lower garnish and center pillar upper garnish.

7. REMOVE LAP BELT OUTER ANCHOR COVER

Click here 8. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY

8. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY

Click here 9. REMOVE CENTER PILLAR LOWER GARNISH

9. REMOVE CENTER PILLAR LOWER GARNISH

Click here 10. REMOVE CENTER PILLAR UPPER GARNISH

10. REMOVE CENTER PILLAR UPPER GARNISH

Click here 11. REMOVE FRONT SEAT OUTER BELT ASSEMBLY

11. REMOVE FRONT SEAT OUTER BELT ASSEMBLY

(a) Remove the nut to disconnect the shoulder anchor.

(b) Using a screwdriver with its tip wrapped in protective tape, release the locking button to disconnect the connector.

Text in Illustration

*a

Protective Tape

(c) Remove the bolt.

(d) Disengage the 2 guides to remove the front seat outer belt assembly.

12. REMOVE FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY

(a) Remove the 2 bolts.

(b) Disengage the guide to remove the front shoulder belt anchor adjuster assembly.

Installation
INSTALLATION CAUTION / NOTICE / HINT HINT: Use the same procedure for both the RH and LH sides. The procedure described below is for the LH side. PROCEDURE 1. INSTALL FRONT SHOU ...

Disposal
DISPOSAL CAUTION / NOTICE / HINT CAUTION: Before performing pre-disposal deployment of any SRS component, review and closely follow all applicable environmental and hazardous material regulations ...

Other materials:

Sound of Portable Player cannot be Heard from Speakers or Sound is Low
PROCEDURE 1. CHECK PORTABLE PLAYER SETTINGS (a) Check the portable player settings. (1) Check that the volume is not set to "0". (2) Check that the mute is off. (b) Check that the sound of the portable player can be heard from the speakers. OK: Sound ...

Yaw Rate Sensor (C1A46)
DESCRIPTION If the millimeter wave radar sensor assembly receives a yaw rate sensor malfunction signal from the yaw rate sensor (airbag sensor assembly) or yaw rate sensor zero point malfunction signal from the skid control ECU (master cylinder solenoid)*1 or skid control ECU (brake actuator ...

Reassembly
REASSEMBLY PROCEDURE 1. INSPECT CENTER NO. 2 SUPPORT BEARING ASSEMBLY (a) Turn the center bearing by hand, check that it turns smoothly without catching and that there are no cracks or damage. If there are any defects, replace it. 2. INSTALL CENTER NO. 2 SUPPORT BEARING ASSEMBLY (a) Instal ...

В© 2011-2024 Copyright www.ttguide.net