Toyota Tacoma (2015-2018) Service Manual: Dtc Check / Clear
DTC CHECK / CLEAR
HINT:
- DTCs which are stored in the ECM can be displayed on the Techstream.
- The Techstream can display pending DTCs and current DTCs. Some DTCs are not stored unless a malfunction is detected in consecutive driving cycles. When a malfunction is detected in only one driving cycle, it is stored as a pending DTC.
1. CHECK DTC (Using Techstream)
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Transmission / Trouble Codes.
(e) Check for DTCs and freeze frame data, and write them down.
|
Techstream Display |
Description |
|---|---|
|
Test Failed |
Shows the malfunction judgment results for the current trip. |
|
Pending |
Shows the malfunction judgment results from when the DTCs were last cleared up until they were checked. (Indicates the possibility of a malfunction when no DTCs are confirmed.) |
|
Confirmed |
Shows the DTCs confirmed up to now. (The number of current trips differs for each DTC.) |
(f) Check the details of the DTCs (See page .gif)
).
NOTICE:
When simulating a symptom and using the Techstream to check for DTCs, use normal mode. For DTCs in the Diagnostic Trouble Code Chart subject to "2 trip detection logic", perform the following:
Turn the ignition switch off after the symptom is simulated once. Then repeat the simulation process. When the symptom has been simulated twice, the MIL will illuminate and DTCs will be stored in the ECM.
2. CLEAR DTC (When Using Techstream)
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Transmission / Clear DTCs.
(e) Clear the DTCs.
3. CLEAR DTC (When not Using Techstream)
(a) Perform either of the following operations:
NOTICE:
After turning ignition switch off, waiting time may be required before disconnecting
the cable from the negative (-) battery terminal. Therefore, make sure to read the
disconnecting the cable from the negative (-) battery terminal notices before proceeding
with work (See page ).
(1) Disconnect the cable from the negative (-) battery terminal for more than 1 minute.
(2) Remove the EFI NO. 1 and ETCS fuses from the engine room relay block, located inside the engine compartment, for more than 1 minute.
Data List / Active Test
DATA LIST / ACTIVE TEST
1. DATA LIST
NOTICE:
In the table below, the values listed under "Normal Condition" are reference
values. Do not depend solely on these reference values when dec ...
Diagnostic Trouble Code Chart
DIAGNOSTIC TROUBLE CODE CHART
Manual Transmission System
DTC Code
Detection Item
MIL
Memory
See page
P03352A
Cranks ...
Other materials:
On-vehicle Inspection
ON-VEHICLE INSPECTION
PROCEDURE
1. INSPECT SIDE AIRBAG SENSOR ASSEMBLY (for Vehicle not Involved in Collision)
(a) Perform a Diagnostic System Check (See page
).
2. INSPECT SIDE AIRBAG SENSOR ASSEMBLY (for Vehicle Involved in Collision and
Airbag has not Deployed)
CAUTION:
For side airbag ...
Disassembly
DISASSEMBLY
PROCEDURE
1. REMOVE FRONT LICENSE PLATE BRACKET
(a) Remove the 2 screws and front license plate bracket.
2. REMOVE NO. 4 ENGINE ROOM WIRE (w/ Fog Light)
(a) Disconnect the 2 connectors.
...
Communication Error from ECM to VSC (P1631)
DESCRIPTION
The ECM sends signals such as A/T information signals, dynamic radar cruise control
operation signals, brake operation demand signals, and buzzer operation demand signals
to the skid control ECU (brake actuator assembly) when the dynamic radar cruise
control is operating. Therefor ...
