DISASSEMBLY
PROCEDURE
1. REMOVE FRONT LICENSE PLATE BRACKET
(a) Remove the 2 screws and front license plate bracket. |
|
2. REMOVE NO. 4 ENGINE ROOM WIRE (w/ Fog Light)
(a) Disconnect the 2 connectors. |
|
(b) Disengage the 8 clamps to remove the No. 4 engine room wire.
3. REMOVE FOG LIGHT ASSEMBLY LH (w/ Fog Light)
(a) for Halogen Fog Light: (1) Remove the screw. (2) Disengage the 2 guides to remove the fog light assembly LH. |
|
(b) for LED Fog Light: (1) Remove the screw. (2) Disengage the 2 guides to remove the fog light assembly LH. |
|
4. REMOVE FOG LIGHT ASSEMBLY RH (w/ Fog Light)
HINT:
Use the same procedure as for the LH side.
5. REMOVE FOG LIGHT COVER LH (w/ Fog Light)
(a) for Halogen Fog Light: (1) Disengage the 6 claws to remove the fog light cover LH. |
|
(b) for LED Fog Light: (1) Disengage the 6 claws to remove the fog light cover LH. |
|
6. REMOVE FOG LIGHT COVER RH (w/ Fog Light)
HINT:
Use the same procedure as for the LH side.
7. REMOVE FRONT BUMPER HOLE COVER LH (w/o Fog Light)
(a) Disengage the 6 claws to remove the front bumper hole cover LH. |
|
8. REMOVE FRONT BUMPER HOLE COVER RH (w/o Fog Light)
HINT:
Use the same procedure as for the LH side.
9. REMOVE LOWER NO. 1 RADIATOR GRILLE
(a) Disengage the 23 claws to remove the lower No. 1 radiator grille. |
|
10. REMOVE FRONT VALANCE PANEL
(a) Remove the 2 outside moulding retainers. |
|
(b) Disengage the 14 claws to remove the front valance panel.
11. REMOVE FRONT FENDER LINER RETAINER
(a) Disengage the claw to remove the front fender liner retainer. |
|
12. REMOVE FRONT BUMPER UPPER CENTER RETAINER
(a) Disengage the 2 clamps to separate the wire harness. |
|
(b) Remove the 6 nuts and front bumper upper center retainer.
13. REMOVE RADIATOR SIDE DEFLECTOR LH
(a) Remove the clip. |
|
(b) Disengage the 3 claws to remove the radiator side deflector LH.
14. REMOVE RADIATOR SIDE DEFLECTOR RH
HINT:
Use the same procedure as for the LH side.
15. REMOVE FRONT BUMPER ARM MOUNTING BRACKET LH
(a) Remove the 2 bolts. |
|
(b) Disengage the claw to remove the front bumper arm moulding bracket LH.
16. REMOVE FRONT BUMPER ARM MOUNTING BRACKET RH
HINT:
Use the same procedure as for the LH side.
17. REMOVE HEADLIGHT MOUNTING BRACKET
(a) Disengage the 2 claws to remove the headlight mounting bracket. HINT: Use the same procedure for the RH side and LH side. |
|
18. REMOVE FRONT BUMPER ENERGY ABSORBER
(a) Disengage the 9 claws and guide to remove the front bumper energy absorber. |
|
19. REMOVE FRONT BUMPER REINFORCEMENT
(a) Remove the 6 nuts and front bumper reinforcement. |
|
20. REMOVE FRONT BUMPER INNER ARM SUB-ASSEMBLY LH
(a) Put a 7 mm (0.276 in.) drill bit into a drill.
(b) Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill as shown in the illustration.
Standard:
Area |
Specified Condition |
---|---|
A |
5 mm (0.197 in.) |
HINT:
Tape the 7 mm (0.276 in.) drill bit to prevent the drill bit from going too deep.
(c) Lightly press the drill against the 3 rivets and drill off the flanges of the 3 rivets.
CAUTION:
Be careful of the drilled rivet as it may become hot.
NOTICE:
(d) Remove the front bumper inner arm sub-assembly LH.
(e) Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled area.
21. REMOVE FRONT BUMPER INNER ARM SUB-ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
22. REMOVE LOWER FRONT BUMPER RETAINER
HINT:
Use the same procedure for both lower front bumper retainers.
(a) Put a 7 mm (0.276 in.) drill bit into a drill.
(b) Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill as shown in the illustration.
Standard:
Area |
Specified Condition |
---|---|
A |
5 mm (0.197 in.) |
HINT:
Tape the 7 mm (0.276 in.) drill bit to prevent the drill bit from going too deep.
(c) Lightly press the drill against the 2 rivets and drill off the flanges of the 2 rivets.
CAUTION:
Be careful of the drilled rivet as it may become hot.
NOTICE:
(d) Remove the lower front bumper retainer.
(e) Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled area.
23. REMOVE NO. 2 FRONT BUMPER EXTENSION SUB-ASSEMBLY LH
(a) Remove the 3 nuts and No. 2 front bumper extension sub-assembly LH. |
|
24. REMOVE NO. 2 FRONT BUMPER EXTENSION SUB-ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
25. REMOVE FRONT BUMPER COVER INSERT LH
(a) Remove the bolt. |
|
(b) Using a screwdriver, disengage the clip to remove the front bumper cover insert LH as shown in the illustration.
26. REMOVE FRONT BUMPER COVER INSERT RH
HINT:
Use the same procedure as for the LH side.
Dtc Check / Clear
DTC CHECK / CLEAR
HINT:
DTCs which are stored in the ECM can be displayed on the Techstream.
The Techstream can display pending DTCs and current DTCs. Some DTCs
are not stored unless a malfunction is detected in consecutive driving cycles.
When a malfunction is detected in o ...
Stereo Component Amplifier Malfunction (B15A3)
DESCRIPTION
This DTC is stored when a malfunction occurs in the stereo component amplifier
assembly.
DTC No.
DTC Detection Condition
Trouble Area
B15A3
When one of the conditions below is met:
Internal power supply malfun ...
Reassembly
REASSEMBLY
PROCEDURE
1. INSTALL CONSOLE COMPARTMENT DOOR HINGE SUB-ASSEMBLY
(a) Engage the 2 guides to install the console compartment door hinge
sub-assembly.
(b) Install the 4 screws.
(c) Engage the 2 guides and 4 claws ...