Toyota Tacoma (2015-2018) Service Manual: Data List / Active Test

Toyota Tacoma (2015-2018) Service Manual / Rc62f Manual Transmission / Transaxle / Manual Transmission System / Data List / Active Test

DATA LIST / ACTIVE TEST

1. DATA LIST

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

(a) Warm up the engine.

(b) Turn the ignition switch off.

(d) Turn the ignition switch to ON.

(e) Turn the Techstream on.

(f) Enter the following menus: Powertrain / Transmission / Data List.

(g) According to the display on the Techstream, read the Data List.

Transmission

Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
Total Distance Traveled	Total distance traveled/ Min.: 0 km (0 mile) Max.: 16777215 km (10425361 mile)	-	-

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

Total Distance Traveled

Total distance traveled/

Min.: 0 km (0 mile)

Max.: 16777215 km (10425361 mile)

(h) Enter the following menus: Powertrain / Engine / Data List.

(i) According to the display on the Techstream, read the Data List.

Engine

Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
Vehicle Speed	Vehicle speed/ Min.: 0 km/h (0 mph) Max.: 255 km/h (158 mph)	Actual vehicle speed	This is the current vehicle speed. The vehicle speed is detected using the wheel speed sensors. There is a delay in when the vehicle speed data is displayed. Therefore, even if the vehicle speed listed in the freeze frame data is 0 km/h (0 mph), this does not always mean that the malfunction occurred when the vehicle was stopped.
Engine Speed	Engine speed/ Min.: 0 rpm Max.: 16383 rpm	500 to 600 rpm: Idling (shift lever in neutral, engine warmed up and A/C off)	When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed.
Battery Voltage	Battery voltage/ Min.: 0 V Max.: 65.5 V	11 to 14 V: Idling	If 11 V or less, characteristics of some electrical components may change.
BATT Voltage	Battery voltage/ Min.: 0 V Max.: 79.998 V	11 to 14 V: Idling	If 11 V or less, characteristics of some electrical components may change.

Check Mode Procedure

CHECK MODE PROCEDURE 1. DESCRIPTION Check mode has a higher sensitivity to malfunctions and can detect malfunctions that cannot be detected in normal mode. Check mode can also detect all of the ma ...

Dtc Check / Clear

DTC CHECK / CLEAR HINT: DTCs which are stored in the ECM can be displayed on the Techstream. The Techstream can display pending DTCs and current DTCs. Some DTCs are not stored unl ...

Other materials:

Vehicle Speed Tolerance Malfunction (C1AA2)
DESCRIPTION The forward recognition camera receives vehicle speed tolerance signals from the combination meter assembly. If the combination meter assembly detects a vehicle speed tolerance malfunction signal, it informs the forward recognition camera via CAN communication, and DTC C1AA2 is st ...

Steering Angle Sensor Internal Circuit (C1433)
DESCRIPTION The skid control ECU (brake actuator assembly) outputs this DTC when it receives an internal malfunction signal from the steering angle sensor. DTC No. Detection Item DTC Detection Condition Trouble Area C1433 St ...

Installation
INSTALLATION PROCEDURE 1. INSTALL POWER STEERING LINK (a) Insert the power steering link into the vehicle in the order shown in the illustration. Install in this Direction (1) Install in this Direction (2) (b) Temporarily install the po ...