Toyota Tacoma (2015-2018) Service Manual: Problem Symptoms Table
PROBLEM SYMPTOMS TABLE
- Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
- Inspect the fuses and relays related to this system before inspecting the suspected areas below.
|
Symptom |
Suspected Area |
See page |
|---|---|---|
|
Only Driver Door LOCK/UNLOCK Functions do not Operate |
Front door lock assembly LH |
|
|
Wire harness or connector |
- |
|
|
Main body ECU (Multiplex network body ECU) |
|
|
|
Driver side junction block |
|
|
|
Only Front Passenger Door LOCK/UNLOCK Functions do not Operate |
Front door lock assembly RH |
|
|
Wire harness or connector |
- |
|
|
Main body ECU (Multiplex network body ECU) |
|
|
|
Driver side junction block |
|
|
|
Only Rear Door LH LOCK/UNLOCK Functions do not Operate |
Rear door lock assembly LH*2 |
|
|
Wire harness or connector |
- |
|
|
Main body ECU (Multiplex network body ECU) |
|
|
|
Driver side junction block |
|
|
|
Only Rear Door RH LOCK/UNLOCK Functions do not Operate |
Rear door lock assembly RH*2 |
|
|
Wire harness or connector |
- |
|
|
Main body ECU (Multiplex network body ECU) |
|
|
|
Driver side junction block |
|
|
|
Speed-sensitive automatic door lock function does not operate (meter / gauge system operates normally) |
Harness or connector |
- |
|
Combination meter assembly |
|
|
|
Main body ECU (Multiplex network body ECU) |
|
|
|
Driver door-linked automatic door unlock function does not operate |
Main body ECU (Multiplex network body ECU) |
|
|
Key lock-in prevention function does not operate |
Unlock warning switch assembly |
|
|
Harness or connector |
- |
|
|
Main body ECU (Multiplex network body ECU) |
|
|
|
All Doors LOCK/UNLOCK Functions do not Operate |
Main body ECU (Multiplex network body ECU) |
|
|
All Doors LOCK/UNLOCK Functions do not Operate Via Door Control Switch or Door Key Cylinder |
Proceed to "All Doors LOCK/UNLOCK Functions do not Operate Via Door Control Switch or Door Key Cylinder" |
|
|
All Doors LOCK/UNLOCK Functions do not Operate Via Door Control Switch |
Proceed to "All Doors LOCK/UNLOCK Functions do not Operate Via Door Control Switch" |
|
|
Lock Operation Continues even after Doors have been Locked*1 |
Front door lock assembly LH |
|
|
Front door lock assembly RH |
|
|
|
Rear door lock assembly LH*2 |
|
|
|
Rear door lock assembly RH*2 |
|
|
|
Wire harness or connector |
- |
|
|
Main body ECU (Multiplex network body ECU) |
|
.gif)
- *1: When the door unlock detection switch detects an unlock position signal after a door lock operation has been performed, a door lock operation will be performed 3 times.
- *2: for Double Cab
Data List / Active Test
DATA LIST / ACTIVE TEST
1. DATA LIST
HINT:
Using the Techstream to read the Data List allows the values or states of switches,
sensors, actuators and other items to be read without removing any p ...
Terminals Of Ecu
TERMINALS OF ECU
1. CHECK DRIVER SIDE JUNCTION BLOCK AND MAIN BODY ECU (MULTIPLEX NETWORK BODY
ECU)
(a) Disconnect the MB main body ECU (multiplex network body ECU) connectors.
(b) Measure the ...
Other materials:
Steering Pad Switch
Components
COMPONENTS
ILLUSTRATION
Removal
REMOVAL
PROCEDURE
1. REMOVE STEERING PAD
(See page
)
2. REMOVE STEERING PAD SWITCH ASSEMBLY
(a) Disconnect the 2 connectors.
(b) Disengage the 2 clamps.
(c) Remove the 4 screws.
...
Speaker Circuit
DESCRIPTION
If there is a short in a speaker circuit, the stereo component amplifier assembly*1
or navigation receiver assembly*2 detects it and stops output to the speakers.
Thus sound cannot be heard from the speakers even if there is no malfunction
in the stereo component amplifier assembly ...
Installation
INSTALLATION
CAUTION / NOTICE / HINT
HINT:
Use the same procedure for both the LH and RH sides.
The procedure described below is for the LH side.
PROCEDURE
1. INSTALL FOG LAMP ASSEMBLY
(a) Engage the 2 guides to install the fog light assembly.
(b) Install the screw.
(c) Con ...
