Toyota Tacoma (2015-2018) Service Manual: Problem Symptoms Table
PROBLEM SYMPTOMS TABLE
HINT:
- Use the table below to help determine the causes of the problem symptom. The potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
- Inspect the fuses and relays related to this system before inspecting the suspected areas below.
|
Symptom |
Suspected Area |
See page |
|---|---|---|
|
Main switch cannot be turned ON (Indicator light on the combination meter does not come on) |
Cruise Control Switch Circuit |
|
|
Cruise Main Indicator Light Circuit |
|
|
|
ECM |
|
|
|
Desired speed cannot be set (Indicator light on the combination meter comes on when the main switch is turned ON, but goes off when operating the "SET" function) |
Cruise Control Switch Circuit |
|
|
ECM |
|
|
|
Desired speed cannot be set (Indicator light on the combination comes on when the main switch is turned ON and it remains ON, while operating the "SET" function) |
Cruise Control Switch Circuit |
|
|
Lighting System |
|
|
|
Clutch Switch Circuit (for Manual Transmission) |
|
|
|
Park/neutral Position Switch Circuit (for AC60E Automatic Transmission) |
|
|
|
Park/neutral Position Switch Circuit (for AC60F Automatic Transmission) |
|
|
|
Combination Meter System |
|
|
|
ECM |
|
|
|
While cruise control driving, the set speed is canceled (Indicator light remains ON) |
Cruise Control Switch Circuit |
|
|
Vehicle Speed Sensor Circuit |
|
|
|
Lighting System |
|
|
|
Cruise Main Indicator Light Circuit |
|
|
|
Clutch Switch Circuit (for Manual Transmission) |
|
|
|
Park/neutral Position Switch Circuit (for AC60E Automatic Transmission) |
|
|
|
Park/neutral Position Switch Circuit (for AC60F Automatic Transmission) |
|
|
|
ECM |
|
|
|
Hunting occurs (Speed is not constant) |
Vehicle Speed Sensor Circuit |
|
|
ECM |
|
|
|
Speed setting cannot be canceled ("CANCEL" function failure only) |
Cruise Control Switch Circuit |
|
|
ECM |
|
|
|
DTC is not output, or is output when should not be |
TC and CG Terminal Circuit |
|
|
ECM |
|
|
|
Cruise Main indicator light does not come on |
Cruise Control Switch Circuit |
|
|
Cruise Main Indicator Light Circuit |
|
|
|
ECM |
|
|
|
Combination Meter Assembly |
|
.gif)
How To Proceed With Troubleshooting
CAUTION / NOTICE / HINT
HINT:
Use the following procedures to troubleshoot the cruise control system.
*: Use the Techstream.
PROCEDURE
1.
VEHICLE BROUGH ...
Road Test
ROAD TEST
HINT:
'SET' and '-', 'RES' and '+', 'ON-OFF' functions share the same switch. Operate
the cruise control main switch according to the directions i ...
Other materials:
Removal
REMOVAL
PROCEDURE
1. REMOVE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
(See page )
2. REMOVE WINDSHIELD WIPER SWITCH ASSEMBLY
3. REMOVE HEADLIGHT DIMMER SWITCH ASSEMBLY
(a) Disconnect the connector.
(b) Disengage the 3 claws to remove the he ...
Speedometer Malfunction
DESCRIPTION
The meter CPU receives vehicle speed signals from the skid control ECU via the
CAN communication system (CAN V1 Bus). The speed sensor detects the wheel speed
and sends the appropriate signals to the skid control ECU. The skid control ECU
supplies power to the vehicle speed sensor ...
Installation
INSTALLATION
PROCEDURE
1. INSTALL OIL COOLER ASSEMBLY (w/ Air Cooled Transmission Oil Cooler)
(a) Install the 2 oil cooler brackets to the oil cooler assembly with the 2 bolts.
Torque:
5.5 N·m {56 kgf·cm, 49 in·lbf}
(b) Install the oil cooler assembly to the vehicle body with th ...
