Toyota Tacoma (2015-2018) Service Manual: Dtc Check / Clear

Toyota Tacoma (2015-2018) Service Manual / 2gr-fks Starting / Smart Key System(for Start Function) / Dtc Check / Clear

DTC CHECK / CLEAR

NOTICE:

When using the Techstream with the engine switch off, connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.

1. CHECK FOR DTC (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) [POWER SOURCE CONTROL])

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(d) Enter the following menus: Body Electrical / Power Source Control / Trouble Codes.

(e) Check for DTCs.

HINT:

Refer to the Techstream operator's manual for further details.

2. CHECK FOR DTC (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) [STARTING CONTROL])

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(d) Enter the following menus: Body Electrical / Starting Control / Trouble Codes.

(e) Check for DTCs.

HINT:

Refer to the Techstream operator's manual for further details.

3. CHECK FOR DTC (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) [SMART KEY])

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(d) Enter the following menus: Body Electrical / Smart Key / Trouble Codes.

(e) Check for DTCs.

HINT:

Refer to the Techstream operator's manual for further details.

4. CLEAR DTC (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) [POWER SOURCE CONTROL])

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(d) Enter the following menus: Body Electrical / Power Source Control / Trouble Codes.

(e) Clear the DTCs by following the directions on the Techstream display.

HINT:

Refer to the Techstream operator's manual for further details.

5. CLEAR DTC (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) [STARTING CONTROL])

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(d) Enter the following menus: Body Electrical / Starting Control / Trouble Codes.

(e) Clear the DTCs by following the directions on the Techstream display.

HINT:

Refer to the Techstream operator's manual for further details.

6. CLEAR DTC (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) [SMART KEY])

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(d) Enter the following menus: Body Electrical / Smart Key / Trouble Codes.

(e) Clear the DTCs by following the directions on the Techstream display.

HINT:

Refer to the Techstream operator's manual for further details.

Diagnosis System

DIAGNOSIS SYSTEM 1. DESCRIPTION (a) Smart key system (for start function) data and the Diagnostic Trouble Codes (DTCs) can be read through the Data Link Connector 3 (DLC3) of the vehicle. When t ...

Terminals Of Ecu

TERMINALS OF ECU 1. CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (a) Disconnect the C27 and C29 certification ECU (smart key ECU assembly) connectors. (b) Measure the voltage and resistance a ...

Other materials:

Data List / Active Test
DATA LIST / ACTIVE TEST 1. DATA LIST NOTICE: In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not. HINT: Using the Techstream to read the Data List allows t ...

On-vehicle Inspection
ON-VEHICLE INSPECTION PROCEDURE 1. INSPECT CURTAIN SHIELD AIRBAG ASSEMBLY (for Vehicle not Involved in Collision) (a) Perform a Diagnostic System Check (See page ). (b) With the curtain shield airbag installed on the vehicle, perform a visual check. If any of the defects mention ...

Driver Side Seat Belt Warning Light does not Operate
DESCRIPTION When the ignition switch is ON, the airbag sensor assembly transmits front seat inner belt status signals to the combination meter assembly through CAN. If the driver seat belt is not fastened, the combination meter assembly blinks the driver side seat belt warning light. If the s ...