TTGuideTacoma manuals & technical reference
HomeAbout carFAQReviewLatestPopularManual indexSearchContacts
Toyota Tacoma (2015-2018) Service Manual / Vf2cm Transfer

Toyota Tacoma (2015-2018) Service Manual: Vf2cm Transfer

  • 4wd Control Ecu
  • 4wd Control Switch
    1. Components
    2. On-vehicle Inspection
    3. Removal
    4. Installation
  • Touch Select 2-4 And High-low System
    1. Parts Location
    2. Precaution
    3. How To Proceed With Troubleshooting
    4. System Description
    5. System Diagram
    6. Diagnosis System
    7. Dtc Check / Clear
    8. Problem Symptoms Table
    9. Terminals Of Ecu
    10. Data List / Active Test
    11. Fail-safe Chart
    12. Freeze Frame Data
    13. Diagnostic Trouble Code Chart
    14. Front Differential Oil Temperature Sensor Circuit Low (P17C7)
    15. Front Differential Oil Temperature Sensor Circuit High (P17C8)
    16. Four Wheel Drive (4WD) Low Switch Circuit Range / Performance (P2772)
    17. Invalid Data Received From Vehicle Dynamics Control Module (U0416)
    18. Automatic Disconnecting Differential Motor Control Circuit Open (P17A0)
    19. Automatic Disconnecting Differential Motor Limit Switch Circuit (P17A4)
    20. Transfer Shift Motor Control Circuit Circuit Open (P17A8)
    21. Four Wheel Drive (4WD) Range Signal Circuit Range / Performance (P279E)
    22. Transfer Shift Motor Control Circuit Low (P17A9)
    23. Transfer Shift Motor Control Circuit High (P17AA)
    24. Transfer Shift Motor Limit Switch Circuit (P17AC)
    25. Clutch Switch Circuit
    26. Lost Communication with ECM / PCM "A" (U0100,U0122)
    27. 4WD Control Switch Circuit
    28. ECU Power Source Circuit
  • Transfer Assembly
    1. Components
    2. Removal
    3. Installation
  • Transfer Case Front Oil Seal
  • Transfer Case Rear Oil Seal
  • Transfer Oil
  • Transfer System
← Previous articleRemovalREMOVAL PROCEDURE 1. REMOVE FRONT WHEEL 2. REMOVE REAR WHEEL 3. REMOVE TIRE PRESSURE WARNING VALVE AND TRANSMITTER (a) Remove the cap and valve core to rel…→ Next article4wd Control EcuComponents COMPONENTS ILLUSTRATION Installation INSTALLATION PROCEDURE 1. INSTALL 4 WHEEL DRIVE CONTROL ECU (a) Engage the 2 guides to install the 4 wheel …

Related Tacoma materials

Checking and replacing fuses
If any of the electrical components do not operate, a fuse may have blown. If this happens, check and replace the fuses as necessary. Turn the engine switch to the LOCK position. The fuses are located in the following places. To check the fuses, follow the instructions below. ...

Dtc Check / Clear
DTC CHECK / CLEAR 1. CHECK DTC (a) Connect the Techstream to the DLC3. (b) Turn the ignition switch to ON. (c) Turn the blind spot monitor main switch assembly (warning canceling switch assembly) on. (d) Turn the Techstream on. (e) Enter the following menus: Body Electrical / Blind Spot Moni ...

Installation
INSTALLATION CAUTION / NOTICE / HINT HINT: Perform "Inspection After Repairs" after replacing the fuel delivery pipe assembly LH (fuel pressure sensor) (See page ). PROCEDURE 1. INSTALL FUEL PIPE PLUG SUB-ASSEMBLY (a) Install a new O-ring, new No. 1 fuel injector back-up ring, new ...

TTGuide

Toyota Tacoma manuals, maintenance guides, service procedures and technical references — organized to help you find the right information faster.

Search the manual library →

Explore

  • Manual index
  • Latest materials
  • Popular materials
  • Search manuals

Tacoma resources

  • Tacoma history
  • Tacoma review
  • Frequently asked questions

Information

  • Contact us
  • Privacy Policy
© 2011-2026 www.ttguide.net. All rights reserved. Independent reference site. Not affiliated with or endorsed by Toyota Motor Corporation. Page generated in 0.0102s