Toyota Tacoma (2015-2018) Service Manual: Terminals Of Ecu
TERMINALS OF ECU
1. CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
(a) Disconnect the A36 air conditioning amplifier assembly connector.
(b) Measure the voltage and resistance according to the value(s) in the table below.
HINT:
Measure the values on the wire harness side with the connector disconnected.
|
Tester Connection |
Wiring Color |
Terminal Description |
Condition |
Specified Condition |
|---|---|---|---|---|
|
A36-17 (B) - Body ground |
LG - Body ground |
Air conditioning amplifier power supply |
Always |
11 to 14 V |
|
A36-1 (IG+) - Body ground |
GR - Body ground |
Air conditioning amplifier power supply |
Ignition switch ON |
11 to 14 V |
|
A36-10 (GND) - Body ground |
W-B - Body ground |
Air conditioning amplifier ground |
Always |
Below 1 Ω |
If the result is not as specified, there may be a malfunction on the wire harness side.
(c) Reconnect the A36 air conditioning amplifier assembly connector.
(d) Measure the voltage and resistance according to the value(s) in the table below.
(e) Check for pulse generation according to the value(s) in the table below.
|
Tester Connection |
Wiring Color |
Terminal Description |
Condition |
Specified Condition |
|---|---|---|---|---|
|
A35-24 (SHP+) - Body ground |
SB - Body ground |
Seat heater (for Front Passenger Side) drive signal |
|
Below 1 V |
|
A35-23 (SHD+) - Body ground |
R - Body ground |
Seat heater (for Driver Side) drive signal |
|
Below 1 V |
|
A36-11 (LIN1) - Body ground |
SB - Body ground |
Seat heater switch signal |
Ignition switch ON |
Pulse generation |
|
A36-31 (TSR) - A35-15 (SG-2) |
BE - P |
Seat heater sensor (for Front Passenger Side) input signal |
Ignition switch off (25°C [77°F]) |
10 kΩ |
|
A36-32 (TSL) - A35-15 (SG-2) |
V - P |
Seat heater sensor (for Driver Side) input signal |
Ignition switch off (25°C [77°F]) |
10 kΩ |
2. CHECK AIR CONDITIONING CONTROL ASSEMBLY
(a) Check the air conditioning control assembly (See page
.gif)
).
Problem Symptoms Table
PROBLEM SYMPTOMS TABLE
HINT:
Use the table below to help determine the cause of problem symptoms.
If multiple suspected areas are listed, the potential causes of the symptoms
are lis ...
Data List / Active Test
DATA LIST / ACTIVE TEST
1. DATA LIST
HINT:
Using the Techstream to read the Data List allows the values or states of switches,
sensors, actuators and other items to be read without removing any p ...
Other materials:
Dtc Check / Clear
DTC CHECK / CLEAR
NOTICE:
When using the Techstream with the engine switch off, connect the Techstream
to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds
or less until communication between the Techstream and the vehicle begins. Then
select the vehicle type u ...
TRAC OFF Indicator Light does not Come ON
DESCRIPTION
Refer to TRAC OFF Indicator Light Remains ON (See page
).
WIRING DIAGRAM
Refer to TRAC OFF Indicator Light Remains ON (See page
).
CAUTION / NOTICE / HINT
NOTICE:
When replacing the skid control ECU (master cylinder solenoid), perform
calibration (See page
).
...
On-vehicle Inspection
ON-VEHICLE INSPECTION
PROCEDURE
1. INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY (w/ Intermittent function)
(a) Remove the steering column cover.
(b) Check the front wiper intermittent operation.
Text in Illustration
*a
Component with harness connected
(Windshield Wiper Sw ...
