Toyota Tacoma (2015-2018) Service Manual: Dtc Check / Clear

Toyota Tacoma (2015-2018) Service Manual / 2gr-fks Starting / Smart Key System(for Start Function) / Dtc Check / Clear

DTC CHECK / CLEAR

NOTICE:

When using the Techstream with the engine switch off, connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.

1. CHECK FOR DTC (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) [POWER SOURCE CONTROL])

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(d) Enter the following menus: Body Electrical / Power Source Control / Trouble Codes.

(e) Check for DTCs.

HINT:

Refer to the Techstream operator's manual for further details.

2. CHECK FOR DTC (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) [STARTING CONTROL])

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(d) Enter the following menus: Body Electrical / Starting Control / Trouble Codes.

(e) Check for DTCs.

HINT:

Refer to the Techstream operator's manual for further details.

3. CHECK FOR DTC (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) [SMART KEY])

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(d) Enter the following menus: Body Electrical / Smart Key / Trouble Codes.

(e) Check for DTCs.

HINT:

Refer to the Techstream operator's manual for further details.

4. CLEAR DTC (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) [POWER SOURCE CONTROL])

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(d) Enter the following menus: Body Electrical / Power Source Control / Trouble Codes.

(e) Clear the DTCs by following the directions on the Techstream display.

HINT:

Refer to the Techstream operator's manual for further details.

5. CLEAR DTC (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) [STARTING CONTROL])

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(d) Enter the following menus: Body Electrical / Starting Control / Trouble Codes.

(e) Clear the DTCs by following the directions on the Techstream display.

HINT:

Refer to the Techstream operator's manual for further details.

6. CLEAR DTC (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) [SMART KEY])

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(d) Enter the following menus: Body Electrical / Smart Key / Trouble Codes.

(e) Clear the DTCs by following the directions on the Techstream display.

HINT:

Refer to the Techstream operator's manual for further details.

Diagnosis System

DIAGNOSIS SYSTEM 1. DESCRIPTION (a) Smart key system (for start function) data and the Diagnostic Trouble Codes (DTCs) can be read through the Data Link Connector 3 (DLC3) of the vehicle. When t ...

Terminals Of Ecu

TERMINALS OF ECU 1. CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (a) Disconnect the C27 and C29 certification ECU (smart key ECU assembly) connectors. (b) Measure the voltage and resistance a ...

Other materials:

Components
COMPONENTS ILLUSTRATION *A w/o Woofer *B w/ Woofer *1 LUGGAGE COMPARTMENT SIDE TRAY LH *2 LUGGAGE COMPARTMENT SIDE TRAY RH ILLUSTRATION *1 COWL SIDE TRIM BOARD LH ...

Short in Front Passenger Side Squib 2nd Step Circuit (B1815/54-B1818/54)
DESCRIPTION The front passenger side squib 2nd step circuit consists of the airbag sensor assembly and the instrument panel passenger without door airbag assembly. The circuit signals the SRS to deploy when airbag deployment conditions are met. These DTCs are set when a malfunction is detected ...

Slip Indicator Light does not Come ON
DESCRIPTION Refer to Slip Indicator Light Remains ON (See page ). WIRING DIAGRAM Refer to Slip Indicator Light Remains ON (See page ). CAUTION / NOTICE / HINT NOTICE: When replacing the skid control ECU (master cylinder solenoid), perform calibration (See page ). Inspe ...