DESCRIPTION
The main body ECU (multiplex network body ECU) controls the low beam headlights.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
PROCEDURE
1. |
PERFORM ACTIVE TEST USING TECHSTREAM (HEADLIGHT RELAY) |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Main Body / Active Test.
(e) Perform the Active Test according to the display on the Techstream.
Main Body
Tester Display |
Test Part |
Control Range |
Diagnostic Note |
---|---|---|---|
Headlight Relay |
Headlight relays |
ON/OFF |
- |
OK:
Headlight relays operate. (Low beam headlights illuminate.)
OK |
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
|
2. |
INSPECT H-LP LO RELAY |
(a) Remove the H-LP LO relay from the engine room relay block. |
|
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection |
Condition |
Specified Condition |
---|---|---|
3 - 5 |
Voltage is not applied between terminals 1 and 2 |
10 kΩ or higher |
3 - 5 |
Voltage is applied between terminals 1 and 2 |
Below 1 Ω |
NG |
REPLACE H-LP LO RELAY |
|
3. |
CHECK HARNESS AND CONNECTOR (BATTERY - H-LP LO RELAY) |
(a) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection |
Condition |
Specified Condition |
---|---|---|
Relay terminal 2 - Body ground |
Always |
11 to 14 V |
Relay terminal 5 - Body ground |
Always |
11 to 14 V |
NG |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
4. |
CHECK HARNESS AND CONNECTOR (H-LP LO RELAY - DRIVER SIDE JUNCTION BLOCK) |
(a) Disconnect the 1F driver side junction block connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection |
Condition |
Specified Condition |
---|---|---|
Relay terminal 1 - 1F-28 |
Always |
Below 1 Ω |
1F-28 - Body ground |
Always |
10 kΩ or higher |
NG |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
5. |
INSPECT DRIVER SIDE JUNCTION BLOCK |
(a) Remove the driver side junction block. |
|
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection |
Condition |
Specified Condition |
---|---|---|
1F-28 - MB-15 (HRLY) |
Always |
Below 1 Ω |
1F-28 - Body ground |
Always |
10 kΩ or higher |
*a |
Component without harness connected (Driver Side Junction Block) |
OK |
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
NG |
REPLACE DRIVER SIDE JUNCTION BLOCK |
Steering Pad Switch
Components
COMPONENTS
ILLUSTRATION
Removal
REMOVAL
PROCEDURE
1. REMOVE STEERING PAD
(See page
)
2. REMOVE STEERING PAD SWITCH ASSEMBLY
(a) Disconnect the 2 connectors.
(b) Disengage the 2 clamps.
(c) Remove the 4 screws.
...
Parts Location
PARTS LOCATION
ILLUSTRATION
*1
FUEL TANK CAP ASSEMBLY
*2
CHARCOAL CANISTER ASSEMBLY
*3
CHARCOAL CANISTER LEAK DETECTION PUMP SUB-ASSEMBLY
*4
PCV VALVE
*5
PURGE VSV
...
Problem Symptoms Table
PROBLEM SYMPTOMS TABLE
HINT:
Troubleshooting of the theft deterrent system is based on the premise
that the power door lock control system, wireless door lock control system*1
and smart key system*2 are operating normally. Accordingly, before troubleshooting
the theft deterrent ...