DATA LIST / ACTIVE TEST
1. DATA LIST
HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch ON.
(c) Turn the Techstream on.
(d) Enter the following menus:
Powertrain / Cruise Control / Data List.
(e) According to the display on the Techstream, read the Data List.
Cruise Control
Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
---|---|---|---|
CCS Vehicle Spd |
Vehicle speed/min.: 0 km/h (0 mph), max.: 255 km/h (158 mph) |
Actual vehicle speed |
- |
CCS Mem Vehicle Spd |
Cruise control memorized speed/min.: 0 km/h (0 mph), max.: 255 km/h (158 mph) |
Actual stored vehicle speed |
- |
Cruise Control |
Cruise control system active condition/ON or OFF |
ON: Cruise control activated OFF: Cruise control deactivated |
- |
CCS Main SW M-CPU |
Main switch signal (Main CPU)/ON or OFF |
ON: Main switch on (Pushed on) OFF: Main switch off (Pushed off) |
"3" |
CCS Ready M-CPU |
Cruise control system standby condition (Main CPU)/ON or OFF |
ON/OFF: Change ON/OFF each time Main SW is pushed in. |
"1" |
CCS Indicator M-CPU |
Cruise indicator signal (Main CPU)/ON or OFF |
ON: "CCS READY" ON OFF: "CCS READY" OFF |
"2" |
Cancel Switch |
CANCEL switch signal/ON or OFF |
ON: CANCEL switch on OFF: CANCEL switch off |
- |
SET/COAST Switch |
-/SET switch signal/ON or OFF |
ON: -/SET switch on OFF: -/SET switch off |
- |
RES/ACC Switch |
+/RES switch signal/ON or OFF |
ON: +/RES switch on OFF: +/RES switch off |
- |
Stop Light SW M-CPU |
Stop light switch signal (Main CPU)/ON or OFF |
ON: Brake pedal depressed OFF: Brake pedal released |
- |
Cruise Operation Status |
PNP switch signal (D position)/ON or OFF |
ON: Shift lever in D OFF: Shift lever not in D |
- |
CCS Request Torque |
Cruise control request torque/min.: -1024 Nm, max.: 1016 Nm |
Actual required torque |
- |
# Codes |
Number of present trouble codes/min.: 0, max.: 255 |
Number of DTCs will be displayed |
- |
HINT:
SRS airbags
The SRS airbags inflate when the vehicle is subjected to certain types of severe
impacts that may cause significant injury to the occupants. They work together with
the seat belts to help reduce the risk of death or serious injury.
Front airbags
Driver airbag/front passenger airbag
Can he ...
Removal
REMOVAL
PROCEDURE
1. REMOVE MANUAL TRANSMISSION ASSEMBLY
(See page )
2. REMOVE CLUTCH RELEASE FORK SUB-ASSEMBLY
(a) Remove the clutch release fork sub-assembly with the clutch release
bearing assembly from the manual transmission assembly.
...
Inspection
INSPECTION
PROCEDURE
1. INSPECT PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY
(a) Using a dial indicator, check the propeller shaft runout.
Maximum runout:
0.6 mm (0.0236 in.)
If the shaft runout is greater than the maximum, replace the shaft.
2. INSPECT PROPELLER SHAFT
(a) Using a dial ...