Toyota Tacoma (2015-2018) Service Manual: How To Proceed With Troubleshooting
CAUTION / NOTICE / HINT
HINT:
- The ECM of this system is connected to the CAN communication system. Therefore, before starting troubleshooting, make sure to check that there is no trouble in the CAN and multiplex communication system.
- *: Use the Techstream.
PROCEDURE
|
1. |
VEHICLE BROUGHT TO WORKSHOP |
|
.gif)
|
2. |
CUSTOMER PROBLEM ANALYSIS |
(a) Refer to the How to Troubleshoot ECU Controlled Systems in Introduction section.
Click here .gif)
|
|
3. |
INSPECT BATTERY VOLTAGE |
Standard voltage:
11 to 14 V
If the voltage is below 11 V, recharge or replace the battery before proceeding.
|
|
4. |
CONNECT TECHSTREAM TO DLC3* |
|
|
5. |
CHECK AND CLEAR DTCS AND FREEZE FRAME DATA* |
(a) Refer to DTC Check/Clear.
Click here
|
|
6. |
VISUAL INSPECTION |
|
|
7. |
SELECT CHECK MODE DIAGNOSIS* |
(a) Refer to Check Mode Procedure.
Click here
|
|
8. |
PROBLEM SYMPTOM CONFIRMATION |
(a) Refer to Road Test.
Click here
|
Result |
Proceed to |
|---|---|
|
Symptom does not occur |
A |
|
Symptom occurs |
B |
| B | .gif) |
GO TO STEP 10 |
|
|
9. |
SYMPTOM SIMULATION |
(a) Refer to Symptom Simulation.
Click here
|
|
10. |
DTC CHECK* |
(a) Refer to DTC Check/Clear.
Click here
|
Result |
Proceed to |
|---|---|
|
DTC is not output |
A |
|
DTC is output |
B |
| B | |
GO TO STEP 18 |
|
|
11. |
BASIC INSPECTION |
(a) Refer to Park/Neutral Position Switch.
Click here
(b) Refer to Shift Lever Assembly.
Click here
| NG | |
GO TO STEP 21 |
|
|
12. |
MECHANICAL SYSTEM TESTS |
(a) Refer to Mechanical System Tests.
Click here
| NG | |
GO TO STEP 17 |
|
|
13. |
HYDRAULIC TEST |
(a) Refer to Hydraulic Test.
Click here
| NG | |
GO TO STEP 17 |
|
|
14. |
MANUAL SHIFTING TEST |
(a) Refer to Manual Shifting Test.
Click here
| NG | |
GO TO STEP 16 |
|
|
15. |
PROBLEM SYMPTOMS TABLE CHAPTER 1 |
(a) Refer to Problem Symptoms Table.
Click here
| NG | |
GO TO STEP 19 |
|
|
16. |
PROBLEM SYMPTOMS TABLE CHAPTER 2 |
(a) Refer to Problem Symptoms Table.
Click here
|
|
17. |
COMPONENT INSPECTION |
| NEXT | |
GO TO STEP 21 |
|
18. |
DTC CHART |
(a) Refer to Diagnostic Trouble Code Chart.
Click here
|
|
19. |
CIRCUIT INSPECTION |
|
|
20. |
IDENTIFICATION OF PROBLEM |
|
|
21. |
REPAIR OR REPLACE |
|
|
22. |
CONFIRMATION TEST |
| NEXT | |
END |
Parts Location
PARTS LOCATION
ILLUSTRATION
ILLUSTRATION
ILLUSTRATION
...
System Description
SYSTEM DESCRIPTION
1. SYSTEM DESCRIPTION
(a) The Electronic Controlled Automatic Transmission (ECT) is an automatic transmission
that has its shift timing electronically controlled by the ECM. The ...
Other materials:
LVDS Signal Malfunction (from Extension Module) (B1532)
DESCRIPTION
The stereo component tuner assembly and the radio and display receiver assembly
are connected by an LVDS communication line.
This DTC is stored when an LVDS communication error occurs between the stereo
component tuner assembly and the radio and display receiver assembly.
...
Problem Symptoms Table
PROBLEM SYMPTOMS TABLE
HINT:
Use the table below to help determine the cause of problem symptoms.
If multiple suspected areas are listed, the potential causes of the symptoms
are listed in order of probability in the "Suspected Area" column of the
table. Check each sy ...
Installation
INSTALLATION
PROCEDURE
1. INSTALL TRANSFER POSITION SWITCH (for 4WD)
Click here
2. INSTALL ENGINE SWITCH
Click here
3. INSTALL AIR CONDITIONING CONTROL ASSEMBLY
(a) Connect the connectors.
(b) Engage the 8 clips to install the air conditioning control assembly.
4. INSTALL RADIO AND DISP ...
