Toyota Tacoma (2015-2018) Service Manual: Automatic Transmission System(for 2tr-fe)
- Precaution
- Definition Of Terms
- Parts Location
- How To Proceed With Troubleshooting
- System Description
- System Diagram
- Hydraulic Test
- Mechanical System Tests
- Road Test
- Initialization
- Manual Shifting Test
- Monitor Drive Pattern
- Problem Symptoms Table
- Diagnosis System
- Dtc Check / Clear
- Terminals Of Ecm
- Check Mode Procedure
- Data List / Active Test
- Fail-safe Chart
- Diagnostic Trouble Code Chart
- Vehicle Control History
- Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT) (P2716)
- Transmission Fluid Temperature Sensor "B" Circuit Low Input (P2742,P2743)
- Short in Torque Converter Clutch Solenoid Circuit (Shift Solenoid Valve SL) (P2769,P2770)
- Transmission Range Sensor Circuit Malfunction (PRNDL Input) (P0705)
- Pressure Control Solenoid "D" Performance (Shift Solenoid Valve SLT) (P2714)
- Transmission Fluid Temperature Sensor "A" Circuit Low Input (P0712,P0713)
- Pressure Control Solenoid "G" Performance (Shift Solenoid Valve SL4) (P2808)
- Pressure Control Solenoid "G" Electrical (Shift Solenoid Valve SL4) (P2810)
- Pressure Control Solenoid "C" Electrical (Shift Solenoid Valve SL3) (P0798)
- Torque Converter Clutch Pressure Control Solenoid Control Circuit Electrical (Shift Solenoid Valve SLU) (P2759)
- Pressure Control Solenoid "B" Electrical (Shift Solenoid Valve SL2) (P0778)
- Pressure Control Solenoid "C" Performance (Shift Solenoid Valve SL3) (P0796)
- Pressure Control Solenoid "A" Performance (Shift Solenoid Valve SL1) (P0746)
- Pressure Control Solenoid "A" Electrical (Shift Solenoid Valve SL1) (P0748)
- Pressure Control Solenoid "B" Performance (Shift Solenoid Valve SL2) (P0776)
- Input Speed Sensor Circuit No Signal (P0717,P07BF,P07C0)
- Output Speed Sensor Circuit No Signal (P0722,P077C,P077D)
- Transmission Fluid Temperature Sensor "A" Performance (P0711)
- Pattern Select Switch Power Mode Circuit
- Transmission Control Switch Circuit
Pattern Select Switch Power Mode Circuit
DESCRIPTION
The ECM memory contains the programs for the normal and PWR shift patterns.
By following the programs corresponding to the signals from the pattern select
switch assembly, park/neutral ...
Precaution
PRECAUTION
1. PRECAUTION
NOTICE:
When disconnecting the cable from the negative (-) battery terminal,
initialize the following systems after the cable is reconnected (See page
).
...
Other materials:
Initialization
INITIALIZATION
1. PROCEDURES NECESSARY WHEN BATTERY TEMINAL IS DISCONNECTED/RECONNECTED
Necessary Procedure
Effect/Inoperative Function when Necessary Procedures are not Performed
Link
Perform steering sensor zero point calibration
Lane ...
Diagnostic Trouble Code Chart
DIAGNOSTIC TROUBLE CODE CHART
Charging System
DTC Code
Detection Item
Warning Indicate
Memory
SAE
See page
P161A87
Lost Communication with Alternator Missing Message
-
DTC stored
...
Disassembly
DISASSEMBLY
PROCEDURE
1. REMOVE MILLIMETER WAVE RADAR WIRE (w/ Toyota Safety Sense P)
Click here
2. REMOVE MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Toyota Safety Sense P)
Click here
3. REMOVE NO. 1 RADIATOR GRILLE GARNISH
(a) When Replacing the No. 1 Radiator Grille Garnish:
(1) Apply p ...
