FAIL-SAFE CHART
HINT:
If any of the following auto cancel conditions are detected while the dynamic radar cruise control system is controlling vehicle speed, the system clears the stored vehicle speed and cancels control of vehicle speed by the dynamic radar cruise control system.
Automatic Cancel Control
Constant Speed Control Mode:
Auto Cancel Condition |
Warning |
Fail-safe Deactivation Condition |
|||
---|---|---|---|---|---|
Multi-information Display |
Master Warning Light |
Cruise Control Indicator |
Warning Buzzer |
||
Open or short in stop light switch circuit |
Cruise Control Malfunction Visit Your Dealer |
Illuminates |
Does not illuminate |
Sounds |
Dynamic radar cruise control system is turned off and back on again using the cruise control main switch (ON-OFF button). |
|
Cruise Control Malfunction Visit Your Dealer |
Illuminates |
Does not illuminate |
Sounds |
Ignition switch ON again. |
If the following condition occurs, the ECM cancels control of vehicle speed by the dynamic radar cruise control system (stored vehicle speed is maintained):
|
- |
Does not illuminate |
Illuminates |
- |
Cruise control main switch is pushed to +RES |
Malfunction in SFI system |
- |
Illuminates |
Does not illuminate |
- |
Dynamic radar cruise control system is turned off and back on again using the cruise control main switch (ON-OFF button). |
Vehicle speed is less than stored vehicle speed by approximately 16 km/h (10 mph) or more |
- |
Does not illuminate |
Illuminates |
- |
Cruise control main switch is pushed to -SET |
|
- |
Does not illuminate |
Illuminates |
- |
Cruise control main switch is pushed to +RES |
Auto Cancel Condition |
Warning |
Fail-safe Deactivation Condition |
|||
---|---|---|---|---|---|
Multi-information Display |
Master Warning Light |
Cruise Control Indicator |
Warning Buzzer |
||
Open or short in stop light switch circuit |
Cruise Control Malfunction Visit Your Dealer |
Illuminates |
Does not illuminate |
Sounds |
Dynamic radar cruise control system is turned off and back on again using the cruise control main switch (ON-OFF button). |
Malfunction in SFI system |
- |
Illuminates |
Does not illuminate |
- |
Dynamic radar cruise control system is turned off and back on again using the cruise control main switch (ON-OFF button). |
If either of the following conditions occurs, the ECM cancels control of vehicle speed by the dynamic radar cruise control system (stored vehicle speed is maintained):
|
- |
Does not illuminate |
Illuminates |
Sounds |
Cruise control main switch is pushed to +RES |
|
Cruise Control Malfunction Visit Your Dealer |
Illuminates |
Does not illuminate |
Sounds |
Ignition switch ON again. |
If the following condition occurs, the ECM cancels control of vehicle speed by the dynamic radar cruise control system (stored vehicle speed is maintained):
|
Radar Cruise Control Unavailable Clean Sensor |
Illuminates |
Does not illuminate |
Sounds |
The condition returns to normal (the resume function can be operated after fail-safe is deactivated). |
If any of the conditions listed below occurs, the ECM cancels control of vehicle speed by the dynamic radar cruise control system (stored vehicle speed is maintained):
|
Radar Cruise Control Unavailable |
Illuminates |
Does not illuminate |
Sounds |
The conditions return to normal (the resume function can be operated after fail-safe is deactivated). |
|
- |
Does not illuminate |
Illuminates |
- |
Cruise control main switch is pushed to +RES |
Radio Antenna Cord
Components
COMPONENTS
ILLUSTRATION
Removal
REMOVAL
PROCEDURE
1. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY
(See page )
2. REMOVE ANTENNA CORD SUB-ASSEMBLY
(a) Disengage the 4 clamps to remove the antenna cord sub-assembly.
Installation
INSTALLATION
PROCEDURE
1. INSTALL ANTENNA COR ...
Removal
REMOVAL
CAUTION / NOTICE / HINT
HINT:
Use the same procedure for both the RH and LH sides.
The procedure described below is for the LH side.
PROCEDURE
1. PRECAUTION
CAUTION:
Be sure to read Precaution thoroughly before servicing (See page
).
NOTICE:
After turning the ign ...
Electronic Circuit Inspection Procedure
ELECTRONIC CIRCUIT INSPECTION PROCEDURE
1. BASIC INSPECTION
(a) WHEN MEASURING RESISTANCE OF ELECTRONIC PARTS
(1) Unless otherwise stated, all resistance measurements should be made at an
ambient temperature of 20°C (68°F). Resistance measurements may be inaccurate if
measured at high tempe ...