Toyota Tacoma (2015-2018) Service Manual: Customize Parameters
CUSTOMIZE PARAMETERS
NOTICE:
- When the customer requests a change in a function, first make sure that the function can be customized.
- Make a note of the current settings before customizing.
HINT:
The following PCS functions and the pre-collision system sensitivity setting can be changed from their default setting.
CUSTOMIZE PRE-COLLISION SYSTEM
(a) Customizing with the Techstream
(1) Turn the ignition switch off.
(2) Connect the Techstream to the DLC3.
(3) Turn the ignition switch to ON.
(4) Turn the Techstream on.
(5) Enter the following menus: Customize Setting / Others.
(6) Select the setting by referring to the table below.
Others|
Tester Display |
Description |
Default |
Setting |
ECU |
|---|---|---|---|---|
|
PCS Operation State Retention Setting |
Refer to the table below |
OFF |
0:OFF,1:ON |
Millimeter wave radar sensor assembly |
|
PCS Alarm Activation Distance Retention Setting 1 |
Refer to the table below |
OFF |
0:OFF,1:ON |
Millimeter wave radar sensor assembly |
|
PCS Alarm Activation Distance Retention Setting 2 |
Refer to the table below |
ON |
0:OFF,1:ON |
Millimeter wave radar sensor assembly |
|
PCS Alarm Activation Distance Retention Setting 3 |
Refer to the table below |
OFF |
0:OFF,1:ON |
Millimeter wave radar sensor assembly |
|
Customize Setting |
Description |
Setting |
|---|---|---|
|
PCS Operation State Retention Setting |
Function to maintain the pre-collision system on/off setting when the ignition switch is turned off and then to ON. |
OFF: Not maintained (Pre-collision system always turns on) ON: Maintained |
|
PCS Alarm Activation Distance Retention Setting 1 |
Function to maintain the sensitivity setting of the pre-collision system when the pre-collision system is turned off and then on. |
OFF: Not maintained (Setting changes to "Mid") ON: Maintained |
|
PCS Alarm Activation Distance Retention Setting 2 |
Function to maintain the sensitivity setting of the pre-collision system when the ignition switch is turned off while the pre-collision system is on. |
OFF: Not maintained (Setting changes to "Mid") ON: Maintained |
|
PCS Alarm Activation Distance Retention Setting 3 |
Function to maintain the sensitivity setting of the pre-collision system when the ignition switch is turned off while the pre-collision system is off. |
OFF: Not maintained (Setting changes to "Mid") ON: Maintained |
System Diagram
SYSTEM DIAGRAM
Communication Table
Sender
Receiver
Signal
Line
Millimeter Wave Radar Sensor Assembly
Forward Recognition Ca ...
How To Proceed With Troubleshooting
CAUTION / NOTICE / HINT
HINT:
Use the following procedure to troubleshoot the pre-collision system.
*: Use the Techstream.
PROCEDURE
1.
VEHICLE BROUGHT ...
Other materials:
Under Hood
General Maintenance
GENERAL MAINTENANCE
PROCEDURE
1. GENERAL NOTES
Maintenance items may vary from country to country. Check the owner's
manual supplement in which the maintenance schedule is shown.
Every service item in the periodic maintenance schedule must be performed.
...
Installation
INSTALLATION
PROCEDURE
1. INSTALL VANE PUMP
(a) Install the vane pump assembly with the 2 bolts.
Torque:
21 N·m {214 kgf·cm, 15 ft·lbf}
(b) Connect the oil pressure switch connector.
NOTICE:
Make sure that no oil adheres to the connector.
...
Inspection
INSPECTION
PROCEDURE
1. INSPECT TIE ROD END SUB-ASSEMBLY
(a) Flip the ball joint stud back and forth 5 times as shown in the illustration
before installing the nut.
(b) Using a torque wrench, turn the nut continuously at a rate of 2 to 4 seconds
per turn and check the torque reading on the ...
