Toyota Tacoma (2015-2018) Service Manual: Cruise Main Indicator Light Circuit

Toyota Tacoma (2015-2018) Service Manual / Cruise Control / Dynamic Radar Cruise Control System(for 2tr-fe) / Cruise Main Indicator Light Circuit

DESCRIPTION

When the dynamic radar cruise control system is turned on using the cruise control main switch (ON-OFF button), the cruise control indicator (vehicle-to-vehicle distance control mode) illuminates. The ECM uses this and other indicators to indicate the control condition (presence or absence of a preceding vehicle, vehicle-to-vehicle distance, and set vehicle speed) and fail-safe state via CAN communication.

CAUTION / NOTICE / HINT

NOTICE:

Before replacing the ECM, refer to Registration.
w/o Smart Key System: Click here

w/ Smart Key System: Click here
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

PROCEDURE

1.	PERFORM ACTIVE TEST USING TECHSTREAM (METER DISPLAY 1)

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(d) Enter the following menus: Body Electrical / Combination Meter / Active Test.

(e) Perform the Active Test according to the display on the Techstream.

Body Electrical > Combination Meter > Active Test

Tester Display	Measurement Item	Control Range	Diagnostic Note
Meter Display 1	Multi-information display	OFF, 6 to 0 or All	-

Result	Proceed to
The multi-information display in the combination meter assembly turns on or off according to the operation of the Active Test.	A
The multi-information display in the combination meter assembly does not turn on or off according to the operation of the Active Test.	B

GO TO METER / GAUGE SYSTEM

2.	READ VALUE USING TECHSTREAM (CRUISE READY MAIN-CPU, CRUISE READY SUB-CPU, CRUISE INDICATOR)

(a) Enter the following menus: Powertrain / Radar Cruise1 / Data List.

(b) Read the Data List according to the display on the Techstream.

Powertrain > Radar Cruise1 > Data List

Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
Cruise Ready Main-CPU	Cruise control system standby condition	ON or OFF	Each time cruise control main switch (ON-OFF button) is pushed, ON or OFF changes	-
Cruise Ready Sub-CPU	Cruise control system standby condition	ON or OFF	Each time cruise control main switch (ON-OFF button) is pushed, ON or OFF changes	-
Cruise Indicator	Cruise control indicator status	ON or OFF	ON: Cruise control indicator illuminates OFF: Cruise control indicator turns off	-

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Cruise Ready Main-CPU

Cruise control system standby condition

ON or OFF

Each time cruise control main switch (ON-OFF button) is pushed, ON or OFF changes

Cruise Ready Sub-CPU

Cruise control system standby condition

ON or OFF

Each time cruise control main switch (ON-OFF button) is pushed, ON or OFF changes

Cruise Indicator

Cruise control indicator status

ON or OFF

ON: Cruise control indicator illuminates

OFF: Cruise control indicator turns off

Result	Proceed to
The cruise control indicator illuminates and turns off according to the operation of the cruise control main switch (ON-OFF button).	A
The cruise control indicator does not illuminate but the Data List item Cruise Indicator changes according to the operation of the cruise control main switch (ON-OFF button).	B
The cruise control indicator does not illuminate and the Data List item Cruise Indicator does not change according to the operation of the cruise control main switch (ON-OFF button).	C

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

REPLACE COMBINATION METER ASSEMBLY

REPLACE ECM

Distance Control Switch Circuit

DESCRIPTION The distance control switch is used to set the distance for vehicle-to-vehicle distance control mode. The distance control switch is installed in the steering pad switch assembly. The ...

Cruise SET Indicator Light Circuit

DESCRIPTION The ECM illuminates the cruise control SET indicator by sending indicator output demand signals to the combination meter assembly via CAN communication. The cruise control SET indicat ...

Other materials:

Pressure Control Solenoid "G" Performance (Shift Solenoid Valve SL4) (P2808)
SYSTEM DESCRIPTION The ECM uses the vehicle speed signal and signals from the transmission revolution sensors (NT, SP2) to detect the actual gear (1st, 2nd, 3rd, 4th, 5th or 6th gear). The ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical problems of t ...

Customize Parameters
CUSTOMIZE PARAMETERS 1. CUSTOMIZING FUNCTION WITH TECHSTREAM NOTICE: When the customer requests a change in a function, first make sure that the function can be customized. Be sure to make a note of the current settings before customizing. When troubleshooting a function, f ...

Microphone Circuit between Microphone and Radio Receiver
DESCRIPTION The navigation receiver assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines. Using this circuit, the navigation receiver assembly sends power to the telephone microphone assembly and the telephone microphone ...