Toyota Tacoma (2015-2018) Service Manual: Portable Player cannot be Connected Manually/Automatically

Toyota Tacoma (2015-2018) Service Manual / Audio / Video / Audio And Visual System / Portable Player cannot be Connected Manually/Automatically

CAUTION / NOTICE / HINT

HINT:

Some versions of "Bluetooth" compatible audio players may not function, or the function may be limited using the radio and display receiver assembly, even if the portable audio player itself can play files (See page PROCEDURE ).

PROCEDURE

1.	CHECK CONNECTED DEVICE SETTINGS

(a) Check if the portable player is registered as a connected device.

NOTICE:

If a cellular phone is used as a portable player, it must be registered independently from the registration that is performed for the hands-free system.

HINT:

Only 5 portable players can be registered.

Result

Result	Proceed to
The portable player is registered as a connected device	A
The portable player is not registered as a connected device	B

2.	CHECK SYMPTOMS

(a) Check the connection condition between the portable player and radio and display receiver assembly.

The portable player cannot be connected under any of the following conditions:

The portable player is connected to another device.
The portable player is connected to the radio and display receiver assembly using the hands-free function.
The radio and display receiver assembly has cleared the portable player registration.
The portable player is off.

Result

Result	Proceed to
The portable player cannot be connected automatically	A
The portable player cannot be connected manually	B

GO TO STEP 4

3.	CHECK AUTOMATIC CONNECTION SETTINGS

(a) Check automatic connection settings of the "Bluetooth" audio.

(1) Check if "On" is displayed for "Bluetooth Power" on the "Detailed Bluetooth Settings" screen.

OK:

"On" is displayed for "Bluetooth Power".

TURN "Bluetooth" POWER TO "On"

4.	CHECK PORTABLE PLAYER STATUS

(a) Check the status of the portable player.

(1) Check that the portable player is not in standby mode.

(2) Check that the portable player is not connected to another device (headphones etc.).

OK:

The portable player is not in standby mode and not connected to another device (headphones etc.).

TAKE PORTABLE PLAYER OUT OF STANDBY MODE AND DISCONNECT OTHER DEVICES (HEADPHONES etc.)

5.	CHECK USING ANOTHER "Bluetooth" AUDIO COMPATIBLE VEHICLE OF SAME MODEL

(a) Check if the portable player can be connected manually/automatically on another "Bluetooth" audio compatible vehicle of the same model.

OK:

The portable player can be connected manually/automatically.

PORTABLE PLAYER IS NOT COMPATIBLE

6.	REMOVE ADDITIONAL DEVICES WHICH USE RADIO WAVES

(a) Remove additional devices which use radio waves.

(b) Check if the portable player can be connected manually/automatically.

OK:

The portable player can be connected manually/automatically.

END

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

Noise Occurs or Sound Skips when Portable Player Plays

CAUTION / NOTICE / HINT HINT: Perform this check with the portable player volume set at an appropriate level. Make sure that there are no obstructions between the portable player ...

Registered Device cannot be Deleted

PROCEDURE 1. DELETE OPERATION (a) Check if a registered portable player can be deleted normally. OK: Registered portable player can be deleted normally. OK ...

Other materials:

On-vehicle Inspection
ON-VEHICLE INSPECTION PROCEDURE 1. INSPECT FRONT WIPER MOTOR (for Driver Side) Text in Illustration *a Matchmark (a) Check the stop (park) position. (b) Operate the windshield wiper motor assembly. (c) Stop the windshield wiper motor assembly operation. (d) Ch ...

System Diagram
SYSTEM DIAGRAM HINT: Each tire pressure warning valve and transmitter sends its transmitter ID, temperature and tire pressure information to the tire pressure warning ECU and receiver. Transmitting ECU (Transmitter) Receiving ECU Signal Communicat ...

Pressure Control Solenoid "G" Performance (Shift Solenoid Valve SL4) (P2808)
SYSTEM DESCRIPTION The ECM uses the vehicle speed signal and signals from the transmission revolution sensors (NT, SP2) to detect the actual gear (1st, 2nd, 3rd, 4th, 5th or 6th gear). The ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical problems of t ...