Toyota Tacoma manuals

Toyota Tacoma 2015-2018 Service Manual: Operation Check

OPERATION CHECK

1. NOTICE WHEN CHECKING THE FOLLOWING

(a) Wireless door lock/unlock function:

This wireless door lock control function operates only when the following 3 conditions are met:

(1) There is no key in the ignition key cylinder.

(2) All doors are closed.

(3) The power door lock system is operating normally.

HINT:

The unlock function operates even when a door is open.

(b) The size of the wireless door lock control operation area differs depending on the situation.

(1) The size of the operation area differs depending on the user and the way the door control transmitter module set sub-assembly is held.

(2) In certain areas, the wireless door lock control function will only operate partially for the operation area, which will be reduced due to the vehicle body shape and the influence of the surrounding environment.

(3) Since the door control transmitter module set sub-assembly uses weak radio waves, strong radio waves or electrical noise in the frequency used by the door control transmitter module set sub-assembly may reduce the size of the operation area and the remote control may not function.

(4) When the transmitter battery is weak, the size of the operation area is reduced and the remote control may not function.

HINT:

If the door control transmitter module set sub-assembly has been left in a place that is exposed to direct sunlight, such as on the instrument panel, it may cause the transmitter battery to be weakened or cause other related problems.

2. CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS

NOTICE:

The operation check below is based on the non-customized initial condition of the vehicle.

HINT:

  • The switches described in this text are the switches for transmitting signals. The switches are built into the door control transmitter module set sub-assembly.
  • All the functions listed below must be checked in comparison with the remote control operation area.

(a) Make sure that the vehicle is in an area that allows the wireless control function to operate.

(b) Check basic functions.

(1) Check that all doors lock when lock switch is pressed.

(2) Check that the driver door unlocks when the unlock switch is pressed once, and unlocks all doors when pressed twice within 5 seconds.

(c) Check the chattering prevention function.

(1) Check that the corresponding operation occurs only once and is not repeated continuously while the switch is held. However, when the switch is operated repeatedly at 1-second intervals, check that the corresponding operation is carried out.

(d) Check the automatic locking function.

(1) Check that the doors relock automatically as long as none of the doors have been opened or all doors have not been locked within approximately 60 seconds after all doors are unlocked by pressing the unlock switch.

(2) Check that the automatic locking function does not operate when any door has been opened within approximately 60 seconds of unlocking the doors by pressing the unlock switch.

(3) Check that the automatic locking function does not operate when all doors have been locked manually (such as using key linked operation, or by pressing the lock switch) within approximately 60 seconds of unlocking the doors by pressing the unlock switch.

(e) Check the switch operation fail-safe function.

(1) Check that the doors cannot be locked or unlocked by operating a switch on an unregistered door control transmitter module set sub-assembly, and that the doors are locked and unlocked by operating a switch on the registered door control transmitter module set sub-assembly.

(f) Check the repeat function.

(1) Check that all doors attempt to automatically lock once again 1 second after the lock switch has been pressed while the driver door control knob is being held in the unlock position.

(g) Check the answer-back (hazard warning light) function.

(1) When the lock switch is pressed, check that the hazard warning lights flash once simultaneously with the locking operation of all doors.

(2) When the unlock switch is pressed once, check that the hazard warning lights flash twice simultaneously with the unlocking operation of the driver door.

(h) Check the answer-back (wireless door lock buzzer) function.

(1) When the lock switch is pressed, check that the buzzer sounds once simultaneously with the locking operation of all doors.

(2) When the unlock switch is pressed once, check that the buzzer sounds twice simultaneously with the unlocking operation of the driver door.

(3) When the luggage compartment door is opened by wireless operation, the wireless door lock buzzer sounds.

(i) Check the panic alarm control function (See page (j) Check the illuminated entry function (See page ).

(j) Check the illuminated entry function (See page (k) Check the sliding roof open function (See page (k) Check the sliding roof open function (See page ).

(k) Check the sliding roof open function (See page Customize Parameters ).

How To Proceed With Troubleshooting
CAUTION / NOTICE / HINT HINT: The wireless door lock control system troubleshooting procedures are based on the premise that the power door lock control system is operating normally. ...

Customize Parameters
CUSTOMIZE PARAMETERS PROCEDURE 1. CUSTOMIZE WIRELESS DOOR LOCK CONTROL SYSTEM HINT: The following items can be customized. NOTICE: When the customer requests a change in a function, firs ...

Other materials:

Rear Differential Lock Position SW Stuck OFF (P17BB)
DESCRIPTION This DTC is output when an OFF malfunction of the differential lock indicator switch is detected. DTC No. Detection Item DTC Detection Condition Trouble Area P17BB Rear Differential Lock Position SW Stuck OFF ...

Transmission Fluid Temperature Sensor "B" Circuit Low Input (P2742,P2743)
DESCRIPTION The No. 2 ATF temperature sensor is installed in the transmission valve body assembly. If the ECM detects an abnormally high ATF temperature near this sensor, it illuminates the warning indicator. HINT: The temperature of ATF easily rises when towing, climbing hills, in ...

Rear Speed Sensor
Removal REMOVAL PROCEDURE 1. PRECAUTION NOTICE: After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notic ...

В© 2011-2020 Copyright www.ttguide.net