Toyota Tacoma manuals

Toyota Tacoma (2005–2015) Owners Manual: Wheels

If a wheel is bent, cracked or heavily corroded, it should be replaced.

Otherwise, the tire may separate from the wheel or cause loss of handling control.

■ Wheel selection

When replacing wheels, care should be taken to ensure that they are equivalent to those removed in load capacity, diameter, rim width, and inset*.

Replacement wheels are available at your Toyota dealer.

*: Conventionally referred to as “offset”.

Toyota does not recommend using: ● Wheels of different sizes or types

● Used wheels

● Bent wheels that have been straightened

■ Wheel precautions

● Use only Toyota wheel nuts and wrench designed for use with your aluminum wheels.

● When rotating, repairing or changing your tires, check that the wheel nuts are still tight after driving 100 miles (160 km).

● Be careful not to damage the aluminum wheels when using tire chains.

● Use only Toyota genuine balance weights or equivalent and a plastic or rubber hammer when balancing your wheels.

■When replacing wheels

The wheels of your Toyota are equipped with tire pressure warning valves and transmitters (except for spare tire) that allow the tire pressure warning system to provide advanced warning in the event of a loss in tire inflation pressure. Whenever wheels are replaced, the tire pressure warning valves and transmitters must be installed.

CAUTION

■When replacing wheels

●Do not use wheels that are a different size from those recommended in the Owner’s Manual, as this may result in loss of handling control.

●Never use an inner tube in a leaking wheel which is designed for a tubeless tire. Doing so may result in an accident, causing death or serious injury.

■When installing the wheel nuts

●Be sure to install the wheel nuts with the tapered end facing inward. Installing

●Be sure to install the wheel nuts with the tapered end facing inward. Installing the nuts with the tapered end facing outward can cause wheel to break and eventually cause a wheel to come off while driving, which could lead to an accident resulting in death or serious injury.

●Never use oil or grease on the wheel bolts or wheel nuts.

Oil and grease may cause the wheel nuts to be excessively tightened, leading to bolt or disc wheel damage. In addition, the oil or grease can cause the wheel nuts to loosen and the wheel may fall off, causing an accident and resulting in death or serious injury. Remove any oil or grease from the wheel bolts or wheel nuts.

NOTICE

■Replacing tire pressure warning valves and transmitters

●Because tire repair or replacement may affect the tire pressure warning valves and transmitters, make sure to have tires serviced by your Toyota dealer or other qualified service shop. In addition, make sure to purchase your tire pressure warning valves and transmitters at your Toyota dealer.

●Ensure that only genuine Toyota wheels are used on your vehicle.

Tire pressure warning valves and transmitters may not work properly with non-genuine wheels.

Tire inflation pressure
■ Tire inflation pressure The recommended cold tire inflation pressure and tire size is displayed on the tire and loading information label. Regular Cab and Double Cab models Access Cab ...

Air conditioning filter
The air conditioning filter must be changed regularly to maintain air conditioning efficiency. ■ Removal method Turn the engine switch to the LOCK position. Open the glove box. Slid ...

Other materials:

Disassembly
DISASSEMBLY PROCEDURE 1. REMOVE STEERING GEAR OUTLET RETURN TUBE (a) Using a union nut wrench, remove the steering gear outlet return tube. 2. REMOVE STEERING TURN PRESSURE TUBE (a) Using a union nut wrench, remove the 2 pressure tubes. (b) Remove the 4 O-rings from the pressure tubes. 3. ...

Maintenance data (fuel, oil level, etc.)
Dimensions 2WD models except PreRunner *: Unladen vehicle 4WD models and PreRunner (except Regular Cab models) *: Unladen vehicle *: Unladen vehicle Vehicle capacity weight 2WD models except PreRunner *: Installing accessories in addition to those installed at the factory increase ...

Brake
General Maintenance GENERAL MAINTENANCE PROCEDURE 1. INSPECT BRAKE LINE PIPES AND HOSES HINT: Work in a well-lighted area. Turn the front wheels fully to the right or left before beginning. (a) Check all the brake lines and hoses for: Damage Wear Deformation Cracks ...

© 2011-2024 Copyright www.ttguide.net