Toyota Tacoma (2015-2018) Service Manual: Navigation / Multi Info Display
Toyota Tacoma (2015-2018) Service Manual / Navigation / Multi Info Display
- Navigation Antenna
- Navigation Receiver
- Navigation System
- Precaution
- Parts Location
- System Diagram
- System Description
- How To Proceed With Troubleshooting
- Operation Check
- Problem Symptoms Table
- Terminals Of Ecu
- Dtc Check / Clear
- Freeze Frame Data
- Data List / Active Test
- Diagnostic Trouble Code Chart
- Lost Communication with Meter (B1324)
- LVDS Signal Malfunction (from Extension Module) (B1532,B156C)
- HD Radio Tuner Malfunction (B1551,B15A0,B15AD,B15B0,B15B3,B15B4,B15B7)
- Extension Module Malfunction (B1552,B158A,B15BA)
- USB Media Malfunction (B1585)
- SD Card Communication Malfunction (B158C)
- AV Signal Stoppage (Low Battery Voltage) (B158F)
- Stereo Component Amplifier Malfunction (B15A3)
- Short in GPS Antenna (B15C0,B15C1)
- Speed Signal Malfunction (B15C2)
- A/C ECU Vehicle Information Reading/Writing Processor Malfunction (B15F5)
- Main Body ECU Vehicle Information Reading/Writing Process Malfunction (B15F6)
- Certification ECU Vehicle Information Reading/Writing Process Malfunction (B15F7)
- XM Tuner Antenna Disconnected (B15FE,B15FF)
- Speaker Output Short (B15C3)
- Sending Malfunction (Navigation to APGS) (U0073,U0100,U0129,U0140,U0155,U0164)
- Stereo Component Amplifier Disconnected (B15D3)
- Voice Recognition Microphone Disconnected (B1579)
- Satellite Radio Broadcast cannot be Received
- Satellite Radio Broadcast cannot be Selected or After Selecting Broadcast, Broadcast cannot be Added into Memory
- Traffic Information is not Displayed
- Noise Occurs
- No Sound can be Heard from Speakers
- Sound Quality is Bad Only when CD is Played (Volume is Too Low)
- CD cannot be Ejected
- CD cannot be Inserted / Played or CD is Ejected Right After Insertion
- CD Sound Skips
- Radio Broadcast cannot be Received or Poor Reception
- Display does not Dim when Light Control Switch is Turned ON
- Illumination for Panel Switch does not Come on with Tail Switch ON
- Panel Switches do not Function
- Screen Flicker or Color Distortion
- Touch Panel Switch does not Function
- Poor Sound Quality in All Modes (Low Volume)
- Vehicle Position Mark Deviates Greatly
- Cursor or Map Rotates when Vehicle Stopped
- GPS Mark is not Displayed
- Voice Guidance does not Function
- Route cannot be Calculated
- Voice is not Recognized
- Cellular Phone Registration Failure, Phone Directory Transfer Failure
- Cellular Phone cannot Send/Receive
- Confirm Cellular Phone Functionality
- Confirm Vehicle Headunit Functionality
- Sound of Portable Player cannot be Heard from Speakers or Sound is Low
- Does not Play even after Bluetooth Audio Mode is Selected
- Portable Player cannot be Operated Using In-vehicle Device or Track Information is not Displayed on In-vehicle Device
- Noise Occurs or Sound Skips when Portable Player Plays
- Portable Player cannot be Connected Manually/Automatically
- Registered Device cannot be Deleted
- Portable Player cannot be Registered
- USB Audio System Recognition/Play Error
- Black Screen
- Steering Pad Switch Circuit
- Vehicle Speed Signal Circuit between Radio Receiver and Combination Meter
- Illumination Circuit
- Parking Brake Switch Circuit
- Speaker Circuit
- Sound Signal Circuit between Radio Receiver and Stereo Component Amplifier
- Data Signal Circuit between Stereo Jack Adapter and Extension Module
- Sound Signal Circuit between Radio Receiver and Stereo Jack Adapter
- Data Signal Circuit between Navigation Receiver Assembly and Extension Module
- Mute Signal Circuit between Radio Receiver and Stereo Component Amplifier
- AVC-LAN Circuit
- Vehicle Speed Signal Circuit between Stereo Component Amplifier and Combination Meter
- Microphone Circuit between Microphone and Radio Receiver
- Radio Receiver Power Source Circuit
- Stereo Component Amplifier Power Source Circuit
On-vehicle Inspection
ON-VEHICLE INSPECTION
PROCEDURE
1. INSPECT GARAGE DOOR OPENER
(a) Press each switch and check that the red LED turns on. If one or
more of the switches does not turn on the LED, conf ...
Navigation Antenna
Components
COMPONENTS
ILLUSTRATION
Installation
INSTALLATION
PROCEDURE
1. INSTALL NAVIGATION ANTENNA ASSEMBLY
(a) Install the navigation antenna assembly with the 2 screws.
(b) Engage th ...
Other materials:
Dtc Check / Clear
DTC CHECK / CLEAR
1. CHECK DTC (for TIRE PRESSURE WARNING ECU AND RECEIVER) (USING TECHSTREAM)
(a) Turn the ignition switch off.
(b) Connect the Techstream to the DLC3.
(c) Turn the ignition switch to ON.
(d) Turn the Techstream on.
(e) Enter the following menus: Chassis / Tire Pressure Monito ...
Blind Spot Monitor Slave Module Beam Axis Inspection Incomplete (C1ABC)
DESCRIPTION
This DTC is stored when a beam axis inspection has not been performed for the
blind spot monitor sensor RH.
HINT:
This DTC is always stored after replacing a blind spot monitor sensor. The purpose
of this DTC is to ensure that beam axis inspection is performed. Completing the
be ...
Terminals Of Ecu
TERMINALS OF ECU
1. CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
(a) Disconnect the 1D and 1F driver side junction block connectors.
(b) Measure the voltage and resistance according to the value(s) in the table
below.
HINT:
Measure the values on the wire harness side with the connectors ...
В© 2011-2026 Copyright www.ttguide.net
