Toyota Tacoma (2015-2018) Service Manual: Indicator Circuit
DESCRIPTION
The forward recognition camera sends indicator illumination request signals to the combination meter assembly via CAN communication.
CAUTION / NOTICE / HINT
NOTICE:
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
PROCEDURE
|
1. |
READ VALUE USING TECHSTREAM (CAN BUS CHECK) |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: System Select / CAN Bus Check.
|
Result |
Proceed to |
|---|---|
|
All of the ECUs and sensors that are currently connected to the CAN communication system are displayed. |
A |
|
None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed. |
B |
| B | .gif) |
GO TO CAN COMMUNICATION SYSTEM |
|
.gif)
|
2. |
CHECK DTC (HEALTH CHECK) |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: System Select / Health Check.
(e) Check DTCs.
|
Result |
Proceed to |
|---|---|
|
No DTCs are output. |
A |
|
DTCs are output. |
B |
| B | |
GO TO DTC CHART |
|
|
3. |
PERFORM ACTIVE TEST USING TECHSTREAM (METER DISPLAY 1) |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Combination Meter / Active Test.
(e) According to the display on the Techstream, perform the Active Test.
|
Tester Display |
Measurement Item |
Control Range |
Diagnostic Note |
|---|---|---|---|
|
Meter Display 1 |
Multi-information display |
ALL or OFF |
Perform the test with the vehicle stopped and engine idling |
|
Result |
Proceed to |
|---|---|
|
The multi-information display in the combination meter assembly turns on or off according to the operation of the Active Test. |
A |
|
The multi-information display in the combination meter assembly does not turn on or off according to the operation of the Active Test. |
B |
| B | |
GO TO METER / GAUGE SYSTEM |
|
|
4. |
READ VALUE USING TECHSTREAM |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Chassis / LKA/LDA / Data List.
(e) Read the Data List according to the display on the Techstream.
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
LDA Control |
Control status of lane departure alert system |
Prohibit or Permit |
Prohibit: Control prohibited Permit: Control permitted |
- |
|
Result |
Proceed to |
|---|---|
|
The lane departure alert indicator illuminates and turns on according to the operation of the lane departure alert main switch |
A |
|
The lane departure alert indicator does not illuminate but the Data List item LDA Control changes according to the operation of the lane departure alert main switch |
B |
|
The lane departure alert indicator does not illuminate and the Data List item LDA Control does not change according to the operation of the lane departure alert main switch |
C |
| A | |
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
| B | |
REPLACE COMBINATION METER ASSEMBLY |
| C | |
REPLACE FORWARD RECOGNITION CAMERA |
Steering Pad Switch Circuit
DESCRIPTION
The forward recognition camera receives a lane departure alert switch signal
from the steering pad switch assembly.
WIRING DIAGRAM
for 2TR-FE
for 2GR-FKS
CAUTION / NOTICE / HINT ...
Power Source Circuit
DESCRIPTION
This circuit provides power to operate the forward recognition camera.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
Inspect the fuses for circuits related to this system before pe ...
Other materials:
Air Mix Damper Control Servo Motor Circuit (Passenger Side) (B1441/41)
DESCRIPTION
This No. 2 air conditioning radiator damper servo sub-assembly (for front passenger
side air mix) is controlled by the air conditioning amplifier assembly and moves
the air mix damper (for front passenger side) to the desired position.
DTC No.
DTC Detection Co ...
Removal
REMOVAL
CAUTION / NOTICE / HINT
HINT:
Use the same procedures for the RH side and LH side.
The procedures listed below are for the LH side.
When removing the moulding, heat the vehicle body and moulding using
a heat light.
Heating Temperature
Item
...
SRS airbags
The SRS airbags inflate when the vehicle is subjected to certain types of severe
impacts that may cause significant injury to the occupants. They work together with
the seat belts to help reduce the risk of death or serious injury.
Front airbags
Driver airbag/front passenger airbag
Can he ...
