Toyota Tacoma (2015-2018) Service Manual: Vehicle Speed Tolerance Malfunction (C1AA2)

Toyota Tacoma (2015-2018) Service Manual / Cruise Control / Forward Recognition Camera System / Vehicle Speed Tolerance Malfunction (C1AA2)

DESCRIPTION

The forward recognition camera receives vehicle speed tolerance signals from the combination meter assembly. If the combination meter assembly detects a vehicle speed tolerance malfunction signal, it informs the forward recognition camera via CAN communication, and DTC C1AA2 is stored.

DTC No.	Detection Item	DTC Detection Condition	Trouble Area
C1AA2	Vehicle Speed Tolerance Malfunction	3 seconds after the ignition switch is turned to ON, a signal from the combination meter assembly indicating an abnormal vehicle speed tolerance is detected by the forward recognition camera for 50 seconds or more.	Meter/gauge system Combination meter assembly Forward recognition camera

CAUTION / NOTICE / HINT

NOTICE:

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.
If the forward recognition camera has been replaced with a new one, be sure to perform Forward Recognition Camera Axis Adjustment.
Click here
The forward recognition camera system uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to How to Proceed with Troubleshooting.
Click here

PROCEDURE

1.	CHECK FOR DTCs (METER / GAUGE SYSTEM)

HINT:

Forward recognition camera system DTC C1AA2 may be stored due to a malfunction in the meter/gauge system. Therefore it is necessary to check for and troubleshoot meter/gauge system DTCs first.

(a) Check for DTCs.

Click here

Result	Proceed to
Meter/gauge system DTCs are not output	A
Meter/gauge system DTCs are output	B

CHECK METER / GAUGE SYSTEM

2.	CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)

(a) Clear the DTCs.

Click here (b) Make sure that the DTC detection conditions are met.

(b) Make sure that the DTC detection conditions are met.

HINT:

If the conditions are not met, the system cannot detect the malfunction.

Click here

Result	Proceed to
DTC C1AA2 is not output	A
DTC C1AA2 is output	B

USE SIMULATION METHOD TO CHECK

3.	REPLACE FORWARD RECOGNITION CAMERA

(a) Replace the forward recognition camera.

Click here (b) Perform forward recognition camera axis adjustment.

(b) Perform forward recognition camera axis adjustment.

Click here

4.	CHECK DTC OUTPUT (FORWARD RECOGNITION CAMERA SYSTEM)

(a) Clear the DTCs.

Click here (b) Make sure that the DTC detection conditions are met.

(b) Make sure that the DTC detection conditions are met.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

Click here

Result	Proceed to
DTC C1AA2 is not output	A
DTC C1AA2 is output	B

END (FORWARD RECOGNITION CAMERA WAS DEFECTIVE)

REPLACE COMBINATION METER ASSEMBLY

FCM Destination Information Unmatched (C1AA1)

DESCRIPTION When the forward recognition camera is replaced with a new one, the new forward recognition camera attempts to store country specification information received from the main body ECU ...

Front Radar Sensor Region Code Mismatch (C1A0A)

DESCRIPTION The forward recognition camera receives necessary information from the millimeter wave radar sensor assembly. When the forward recognition camera judges that a millimeter wave radar se ...

Other materials:

Data List / Active Test
DATA LIST / ACTIVE TEST 1. READ DATA LIST HINT: Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or sig ...

AVC-LAN Circuit
DESCRIPTION Each unit of the navigation system connected to the AVC-LAN (communication bus) transfers the switch signals using the AVC-LAN. If a short to +B or short to ground occurs in the AVC-LAN, the navigation system will not function normally because communication is not possible. WIRING ...

Brake Booster Pump Motor on Time Abnormally Long (C1252)
DESCRIPTION The motor relay (semiconductor relay) is built into the master cylinder solenoid and drives the pump motor based on a signal from the skid control ECU (master cylinder solenoid). DTC No. DTC Detecting Condition Trouble Areas C1252 ...