Toyota Tacoma (2015-2018) Service Manual: FCM Destination Information Unmatched (C1AA1)

Toyota Tacoma (2015-2018) Service Manual / Cruise Control / Forward Recognition Camera System / FCM Destination Information Unmatched (C1AA1)

DESCRIPTION

When the forward recognition camera is replaced with a new one, the new forward recognition camera attempts to store country specification information received from the main body ECU (multiplex network body ECU) and ECM. If the country specification information stored in the forward recognition camera is different from that stored in the main body ECU (multiplex network body ECU) or ECM, DTC C1AA1 is stored.

DTC No.	Detection Item	DTC Detection Condition	Trouble Area
C1AA1	FCM Destination Information Unmatched	3 seconds after the ignition switch is turned to ON, destination information stored in the forward recognition camera and that received from the main body ECU (multiplex network body ECU) or ECM do not match for 5 seconds or more.	CAN communication system Forward recognition camera Main body ECU (Multiplex network body ECU) ECM

CAUTION / NOTICE / HINT

NOTICE:

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.
If the forward recognition camera has been replaced with a new one, be sure to perform Forward Recognition Camera Learning.
Click here

HINT:

This DTC is stored when the destination information stored in the forward recognition camera and that stored in the main body ECU (multiplex network body ECU) do not match. If the forward recognition camera or main body ECU (multiplex network body ECU) has been replaced, check if a forward recognition camera or main body ECU (multiplex network body ECU) from another vehicle was used.

PROCEDURE

1.	CHECK FOR DTCs (CAN COMMUNICATION DTC OUTPUT)

HINT:

The forward recognition camera communicates with the main body ECU (multiplex network body ECU) via CAN communication. Confirm that the CAN communication system is functioning normally before proceeding.

(a) Check for DTCs.

Click here

Result	Proceed to
DTC U0142 is not output	A
DTC U0142 is output	B

GO TO CAN COMMUNICATION SYSTEM

2.	CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)

(a) Clear the DTCs.

Click here (b) Make sure that the DTC detection conditions are met.

(b) Make sure that the DTC detection conditions are met.

HINT:

If the conditions are not met, the system cannot detect the malfunction.

Click here

Result	Proceed to
DTC C1AA1 is not output	A
DTC C1AA1 is output	B

USE SIMULATION METHOD TO CHECK

3.	REPLACE FORWARD RECOGNITION CAMERA

(a) Replace the forward recognition camera.

Click here (b) Perform forward recognition camera axis adjustment.

(b) Perform forward recognition camera axis adjustment.

Click here

4.	CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)

(a) Clear the DTCs.

Click here (b) Make sure that the DTC detection conditions are met.

(b) Make sure that the DTC detection conditions are met.

HINT:

If the conditions are not met, the system cannot detect the malfunction.

Click here

Result	Proceed to
DTC C1AA1 is not output	A
DTC C1AA1 is output	B

END (FORWARD RECOGNITION CAMERA WAS DEFECTIVE)

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

Skid Control Buzzer Circuit (C1AA7)

DESCRIPTION The forward recognition camera operates the pre-collision warning by sending a buzzer request signal to the skid control buzzer. If the forward recognition camera detects a malfunction ...

Vehicle Speed Tolerance Malfunction (C1AA2)

DESCRIPTION The forward recognition camera receives vehicle speed tolerance signals from the combination meter assembly. If the combination meter assembly detects a vehicle speed tolerance malfun ...

Other materials:

Fail-safe Chart
FAIL-SAFE CHART FAIL-SAFE FUNCTION (a) When a malfunction occurs in the lane departure alert system, a message will be displayed on the multi-information display in the combination meter assembly and the lane departure alert system will be disabled depending on the malfunction. War ...

Steering Angle Sensor Zero Point Malfunction (C1290)
DESCRIPTION The skid control ECU (master cylinder solenoid) acquires steering angle sensor zero point every time the ignition switch is turned to ON and the vehicle is driven at 35 km/h (22 mph) or more for approximately 5 seconds. The ECU also stores the previous zero point. If the front wh ...

Installation
INSTALLATION CAUTION / NOTICE / HINT HINT: Use the same procedure for both the LH and RH sides. The procedure described below is for the LH side. PROCEDURE 1. INSTALL FOG LAMP ASSEMBLY (a) Engage the 2 guides to install the fog light assembly. (b) Install the screw. (c) Con ...