TERMINALS OF ECU
1. CHECK SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)
(a) Disconnect the S50 sliding roof ECU (sliding roof drive gear sub-assembly) connector.
(b) Measure the resistance and voltage according to the value(s) in the table below.
HINT:
Measure the values on the wire harness side with the connector disconnected.
Tester Connection |
Wiring Color |
Terminal Description |
Condition |
Specified Condition |
---|---|---|---|---|
S50-8 (B) - S50-12 (E) |
W - W-B |
Battery power supply |
Always |
11 to 14 V |
S50-1 (IG) - S50-12 (E) |
BE - W-B |
IG power supply |
Ignition switch off |
Below 1 V |
S50-1 (IG) - S50-12 (E) |
BE - W-B |
IG power supply |
Ignition switch ON |
11 to 14 V |
S50-12 (E) - Body ground |
W-B - Body ground |
Ground |
Always |
Below 1 Ω |
If the result is not as specified, there may be a malfunction in the wire harness.
(c) Reconnect the S50 sliding roof ECU (sliding roof drive gear sub-assembly) connector.
(d) Measure the voltage according to the value(s) in the table below.
Tester Connection |
Wiring Color |
Terminal Description |
Condition |
Specified Condition |
---|---|---|---|---|
S50-7 (OPN) - S50-12 (E) |
B - W-B |
Sliding roof motor open |
Ignition switch ON, OPEN switch on |
Below 1 V |
S50-7 (OPN) - S50-12 (E) |
B - W-B |
Sliding roof motor open |
Ignition switch ON, OPEN switch off |
11 to 14 V |
S50-5 (CLS) - S50-12 (E) |
SB - W-B |
Sliding roof motor close |
Ignition switch ON, CLOSE switch on |
Below 1 V |
S50-5 (CLS) - S50-12 (E) |
SB - W-B |
Sliding roof motor close |
Ignition switch ON, CLOSE switch off |
11 to 14 V |
S50-4 (UP) - S50-12 (E) |
LG - W-B |
Sliding roof motor up |
Ignition switch ON, UP switch on |
Below 1 V |
S50-4 (UP) - S50-12 (E) |
LG - W-B |
Sliding roof motor up |
Ignition switch ON, UP switch off |
11 to 14 V |
S50-6 (DWN) - S50-12 (E) |
L - W-B |
Sliding roof motor down |
Ignition switch ON, DOWN switch on |
Below 1 V |
S50-6 (DWN) - S50-12 (E) |
L - W-B |
Sliding roof motor down |
Ignition switch ON, DOWN switch off |
11 to 14 V |
If the result is not as specified, the sliding roof ECU (sliding roof drive gear sub-assembly) may be malfunctioning.
Vacuum Warning Switch
Components
COMPONENTS
ILLUSTRATION
On-vehicle Inspection
ON-VEHICLE INSPECTION
PROCEDURE
1. INSPECT BRAKE FLUID LEVEL IN RESERVOIR
2. INSPECT BRAKE BOOSTER ASSEMBLY
3. INSPECT VACUUM WARNING SWITCH ASSEMBLY
(a) Start the engine and stop it after 1 or 2 minutes.
(b) Disconnect the ...
Lost Communication with ECM/PCM "A" Missing Message (U010087)
DESCRIPTION
The engine control unit and the transmission control unit are located inside
the ECM. The engine control unit intercommunicates with the transmission control
unit with the Controller Area Network (CAN).
If there is a problem in this intercommunication, the ECM stores a DTC.
...
On-vehicle Inspection
ON-VEHICLE INSPECTION
PROCEDURE
1. INSPECT REAR AIRBAG SENSOR (for Vehicle not Involved in Collision)
(a) Perform a diagnostic system check (See page
).
2. INSPECT REAR AIRBAG SENSOR (for Vehicle Involved in Collision and Airbag has
not Deployed)
(a) Perform a diagnostic system check (See p ...