Toyota Tacoma (2015-2018) Service Manual: Removal

Toyota Tacoma (2015-2018) Service Manual / 2gr-fks Emission Control / Canister / Removal

REMOVAL

PROCEDURE

1. REMOVE FUEL TANK ASSEMBLY

Click here 2. DISCONNECT CHARCOAL CANISTER FUEL HOSE

2. DISCONNECT CHARCOAL CANISTER FUEL HOSE

(a) Loosen the hose clip and disconnect the charcoal canister fuel hose.

3. DISCONNECT FUEL TANK VENT HOSE

(a) Push the fuel tank vent hose deep inside.

Push

(b) Pinch portion A to disconnect the fuel tank vent hose as shown in the illustration.

NOTICE:

Remove any dirt and foreign objects from the fuel tank vent hose connector before performing the work.
Do not allow any scratches or foreign objects on the parts when disconnecting, as the fuel tank vent hose connector has the O-ring that seals the pipe.
Perform the work by hand. Do not use any tools.
Do not forcibly bend, twist or turn the nylon tube.
Protect the disconnected part by covering it with a vinyl bag after disconnecting the fuel tank vent hose.
If the fuel tank vent hose connector and pipe are stuck, push and pull them to release.

*1	Fuel Tank Vent Hose Retainer
*2	Fuel Tank Vent Hose Connector
*3	O-ring
	Pinch
	Pull

4. REMOVE CHARCOAL CANISTER ASSEMBLY

(a) Disconnect the 3 connectors.

(b) Disengage the clamp to separate the wire harness.

(d) Disengage the guide to separate the wire harness bracket.

(e) Remove the bolt, 3 nuts and charcoal canister assembly.

5. DISCONNECT FUEL TANK VENT HOSE SUB-ASSEMBLY

(a) Push the fuel tank vent hose sub-assembly deep inside.

Push

(b) Pinch portion A to disconnect the fuel tank vent hose sub- assembly as shown in the illustration.

NOTICE:

Remove any dirt and foreign objects from the fuel tank vent hose sub-assembly connector before performing the work.
Do not allow any scratches or foreign objects on the parts when disconnecting, as the fuel tank vent hose sub-assembly connector has the O-ring that seals the pipe.
Perform the work by hand. Do not use any tools.
Do not forcibly bend, twist or turn the nylon tube.
Protect the disconnected part by covering it with a vinyl bag after disconnecting the fuel tank vent hose sub-assembly.
If the fuel tank vent hose sub-assembly connector and pipe are stuck, push and pull them to release.

*1	Fuel Tank Vent Hose Retainer
*2	Fuel Tank Vent Hose Connector
*3	O-ring
	Pinch
	Pull

6. REMOVE CHARCOAL CANISTER LEAK DETECTION PUMP SUB-ASSEMBLY

(a) Before removing the leak detection pump sub-assembly, clean the canister by blowing air into it to ensure that the canister is free of foreign matter.

NOTICE:

Make sure to clean the canister using only air.
Do not use gasoline, thinners or solvents.

(b) Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws to remove the charcoal canister leak detection pump sub-assembly as shown in the illustration.

*a	Protective Tape

(1) Visually check that the inside of the charcoal canister assembly is free of foreign matter.

(2) Hold the charcoal canister assembly upside down to make sure that the charcoal canister assembly is free of foreign matter. If the charcoal canister assembly contains foreign matter, replace the charcoal canister assembly.

Components

COMPONENTS ILLUSTRATION *1 CHARCOAL CANISTER ASSEMBLY *2 CHARCOAL CANISTER FUEL HOSE *3 CHARCOAL CANISTER LEAK DETECTION PUM ...

Inspection

INSPECTION PROCEDURE 1. INSPECT CHARCOAL CANISTER ASSEMBLY (a) Visually check the charcoal canister assembly. (1) Visually check the charcoal canister assembly for cracks or damage. ...

Other materials:

Main Switch Circuit
DESCRIPTION When the blind spot monitor main switch assembly (warning canceling switch assembly) is turned on, a signal is sent to the blind spot monitor sensor LH. The blind spot monitor system operates according to this signal. WIRING DIAGRAM CAUTION / NOTICE / HINT NOTICE: Inspect the ...

Installation
INSTALLATION CAUTION / NOTICE / HINT HINT: The following procedures are for BD22 (w/o Differential Lock). PROCEDURE 1. INSTALL DIFFERENTIAL CARRIER ASSEMBLY REAR (a) Clean the contact surfaces of the rear differential carrier assembly and axle housing. (b) Install the rear differential carr ...

Dtc Check / Clear
DTC CHECK / CLEAR 1. DTC CHECK / CLEAR (when Using Techstream) (a) Check for DTCs. (1) Connect the Techstream to the DLC3. (2) Turn the ignition switch to ON. (3) Turn the Techstream on. (4) Enter the following menus: Chassis / ABS/VSC/ TRAC / Trouble Codes. (5) Read the DTCs by following the ...