Toyota Tacoma (2015-2018) Service Manual: Inspection
INSPECTION
PROCEDURE
1. INSPECT CHARCOAL CANISTER ASSEMBLY
|
(a) Visually check the charcoal canister assembly. (1) Visually check the charcoal canister assembly for cracks or damage. If cracks or damage are found, replace the charcoal canister assembly. |
|
(b) Check charcoal canister assembly operation.
|
*a |
Vent Port |
|
*b |
Air Inlet Port |
|
*c |
Purge Port |
|
*d |
Air |
|
*e |
Leak Detection Pump Sub-assembly Connector |
(1) With the purge port and leak detection pump sub-assembly connector closed, blow 5 kPa (0.05 kgf/cm2, 0.7 psi) of air into the vent port, and check that air flows from the air inlet port.
If the result is not as specified, replace the charcoal canister assembly.
|
(2) With the vent port and leak detection pump sub-assembly connector closed, blow 5 kPa (0.05 kgf/cm2, 0.7 psi) of air into the air inlet port, and check that air flows from the purge port. If the result is not as specified, replace the charcoal canister assembly. |
|
|
(c) Check for air leaks. (1) Connect a pressure gauge to the vent port of the charcoal canister. (2) With the purge port, air inlet port and leak detection pump sub-assembly connector closed, apply 20 kPa (150 mmHg, 5.91 in.Hg) of pressurized air into the vent port, then confirm that pressure is retained for 1 minute. If the result is not as specified, replace the charcoal canister assembly. |
|
2. INSPECT CHARCOAL CANISTER LEAK DETECTION PUMP SUB-ASSEMBLY
(a) Check the charcoal canister leak detection pump sub-assembly.
|
*a |
Port A |
|
*b |
Port B |
|
*c |
Air |
(1) Check that air flows from port A to port B.
If the result is not as specified, replace the charcoal canister leak detection pump sub-assembly.
|
(2) Connect the positive (+) lead of the battery to terminal 5 and the negative (-) lead to terminal 1. |
|
(3) Check that a clicking sound is heard from the leak detection pump sub-assembly.
If the result is not as specified, replace the charcoal canister leak detection pump sub-assembly.
Removal
REMOVAL
PROCEDURE
1. REMOVE FUEL TANK ASSEMBLY
Click here
2. DISCONNECT CHARCOAL CANISTER FUEL HOSE
(a) Loosen the hose clip and disconnect the charcoal canister fuel hose.
...
Installation
INSTALLATION
PROCEDURE
1. INSTALL CHARCOAL CANISTER LEAK DETECTION PUMP SUB-ASSEMBLY
(a) Engage the 2 claws to install a new charcoal canister leak detection
pump sub-assembly to the ...
Other materials:
Dtc Check / Clear
DTC CHECK / CLEAR
1. SUPPLEMENTAL RESTRAINT SYSTEM DTC CHECK (USING SST CHECK WIRE)
(a) Check the DTCs (Present DTCs).
(1) Turn the ignition switch to ON, and wait for approximately 60 seconds.
(2) Using SST, connect terminals TC and CG of the DLC3.
SST: 09843-18040
NOTICE:
Connect the term ...
Precaution
PRECAUTION
1. PRECAUTION
(a) Before starting work on the fuel system, including inspections and repairs,
disconnect the cable from the negative (-) battery terminal.
(b) Do not smoke or work near fire when performing work on the fuel system.
(c) Keep gasoline away from rubber or leather parts. ...
Brake Switch "A" Circuit (P0571)
DESCRIPTION
Detection condition 1:
When the brake pedal is depressed, the stop light switch assembly outputs
a signal to the ECM. When the ECM receives the signal, it cancels control
of vehicle speed by the dynamic radar cruise control system. The fail-safe
function operates to ...
