REMOVAL
PROCEDURE
1. REMOVE NO. 2 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Off Road Package)
2. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
3. DRAIN ENGINE COOLANT
4. REMOVE RADIATOR GRILLE
(See page )
5. REMOVE V-BANK COVER SUB-ASSEMBLY
6. REMOVE RADIATOR SUPPORT TO FRAME SEAL
7. REMOVE RADIATOR SIDE DEFLECTOR LH
(a) Remove the clip. |
|
(b) Disengage the 3 claws and remove the radiator side deflector LH.
8. REMOVE RADIATOR SIDE DEFLECTOR RH
(a) Remove the clip. |
|
(b) Disengage the 3 claws and remove the radiator side deflector RH.
9. REMOVE NO. 1 RADIATOR HOSE
(a) Slide the 2 hose clips and remove the No. 1 radiator hose from the water outlet and radiator assembly. |
|
10. REMOVE NO. 2 RADIATOR HOSE
(a) Slide the hose clip and disconnect the No. 2 radiator hose from the water inlet with thermostat sub-assembly. |
|
(b) Slide the hose clip and remove the No. 2 radiator hose from the radiator assembly. |
|
11. DISCONNECT RADIATOR RESERVE TANK HOSE
(a) Disconnect the radiator reserve tank hose from the radiator assembly. |
|
12. DISCONNECT TRANSMISSION OIL COOLER HOSE (for Automatic Transmission)
(a) w/o Air Cooled Transmission Oil Cooler:
(1) Disengage the clamp to separate the 2 transmission oil cooler hoses from the fan shroud. |
|
(2) Slide the 2 hose clips and disconnect the 2 transmission oil cooler hoses from the radiator assembly.
(b) w/ Air Cooled Transmission Oil Cooler:
(1) Disengage the clamp to separate the 2 transmission oil cooler hoses from the fan shroud. |
|
(2) Slide the 2 hose clips and disconnect the 2 transmission oil cooler hoses from the radiator assembly.
13. REMOVE FAN SHROUD
(a) Loosen the 4 nuts holding the fan with fluid coupling. |
|
(b) Remove the fan and generator V belt (See page ).
(c) Remove the 2 bolts holding the fan shroud. |
|
(d) Remove the 4 nuts of the fan with fluid coupling, and then remove the fan shroud together with the fan with fluid coupling.
NOTICE:
Be careful not to damage the radiator core.
(e) Remove the fan pulley from the engine water pump assembly.
14. REMOVE RADIATOR ASSEMBLY
(a) Remove the 4 bolts. Text in Illustration
|
|
(b) Disengage the 2 hooks and remove the radiator assembly from the radiator support sub-assembly.
How To Proceed With Troubleshooting
CAUTION / NOTICE / HINT
HINT:
Use the following procedure to troubleshoot the blind spot monitor system.
*: Use the Techstream.
PROCEDURE
1.
VEHICLE BROUGHT TO WORKSHOP
NEXT
...
Washer Level Warning Switch
Components
COMPONENTS
ILLUSTRATION
Inspection
INSPECTION
PROCEDURE
1. INSPECT LEVEL WARNING SWITCH ASSEMBLY
HINT:
This check should be performed with the windshield washer motor and pump assembly
installed on the washer jar.
(a) Fill the washer jar with washer fluid.
(b) ...
Installation
INSTALLATION
PROCEDURE
1. INSTALL HEADLIGHT DIMMER SWITCH ASSEMBLY
(a) Engage the 3 claws to install the headlight dimmer switch assembly.
(b) Connect the connector.
2. INSTALL WINDSHIELD WIPER SWITCH ASSEMBLY
3. INSTALL SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
(See page ) ...