Toyota Tacoma (2015-2018) Service Manual: Disassembly

Toyota Tacoma (2015-2018) Service Manual / 2gr-fks Cooling / Radiator / Disassembly

DISASSEMBLY

PROCEDURE

1. REMOVE RADIATOR DRAIN COCK PLUG

(a) Remove the radiator drain cock plug from the radiator assembly.

(b) Remove the O-ring from the radiator drain cock plug.

2. REMOVE RADIATOR TO SUPPORT SEAL

(a) Remove the 2 radiator to support seals from the radiator assembly.

Text in Illustration

*1	Radiator to Support Seal

3. REMOVE RADIATOR SUPPORT BUSHING

(a) Remove the 2 No. 1 radiator support collars and 2 No. 1 radiator support bushings from the radiator assembly.

Text in Illustration

*1	No. 1 Radiator Support Collar
*2	No. 2 Radiator Support Collar
*3	No. 1 Radiator Support Bushing
*4	No. 2 Radiator Support Bushing

(b) Remove the 2 No. 2 radiator support collars and 2 No. 2 radiator support bushings from the radiator assembly.

4. ASSEMBLE SST

(a) Engage the claw with the overhaul handle by inserting it into the hole in part A as shown in the illustration.

Text in Illustration

*a	SST (Overhaul Handle)
*b	SST (Claw)
*c	Part A
*d	Dimension B
*e	Stopper Bolt

SST: 09230-01010

09231-01010

09231-01030

(b) While gripping the handle, adjust dimension B to between 0.2 and 0.3 mm (0.00787 and 0.0118 in.), using the stopper bolt.

Dimension B:

0.2 to 0.3 mm (0.00787 to 0.0118 in.)

NOTICE:

If the stopper bolt cannot be adjusted, the claw may be damaged.

5. UNCAULK CORE PLATE

(a) Straighten the core plate by gripping it with SST until stopped by the stopper bolt.

Text in Illustration

*1	Radiator Tank
*2	Core Plate
*a	Stopper Bolt

SST: 09230-01010

09231-01010

09231-01030

6. REMOVE UPPER RADIATOR TANK

(a) Lightly tap the radiator tank bracket (or radiator tank pipe) with a plastic hammer to remove the upper radiator tank.

7. REMOVE LOWER RADIATOR TANK

HINT:

Perform the same procedures as for the upper radiator tank.

On-vehicle Inspection

ON-VEHICLE INSPECTION PROCEDURE 1. INSPECT RADIATOR CAP SUB-ASSEMBLY CAUTION: Do not remove the radiator cap sub-assembly while the engine and radiator assembly are still hot. Pressurized, hot e ...

Removal

REMOVAL PROCEDURE 1. REMOVE NO. 2 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Off Road Package) 2. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY 3. DRAIN ENGINE COOLANT 4. REMOVE RADIATOR GRILLE (See ...

Other materials:

SRS airbag instructions for Canadian owners (in French)
The following is a French explanation of SRS airbag instructions extracted from the SRS airbag section in this manual. See the SRS airbag section for more detailed SRS airbag instructions in English. ...

Installation
INSTALLATION CAUTION / NOTICE / HINT CAUTION: Be sure to perform this procedure with several people as the transfer assembly is very heavy. PROCEDURE 1. INSTALL TRANSFER CASE LOWER PROTECTOR (a) Install the transfer case lower protector with the 4 bolts. Torque: 18 N·m {184 kgf·cm, 13 f ...

Initialization not Completed (C2177/77)
DESCRIPTION Initialization is necessary if one of the following occurs: The tire pressure warning ECU and receiver is replaced. A tire pressure warning valve and transmitter is replaced. Tires with different standard tire pressures are installed. The tires are rotated. A new ...