DESCRIPTION
The air conditioning control assembly communicates with the air conditioning amplifier assembly through the LIN communication system.
If the LIN communication system malfunctions, the air conditioning amplifier assembly does not operate even if the air conditioning control assembly is operated.
DTC No. |
DTC Detection Condition |
Trouble Area |
---|---|---|
B14B3 |
Lost communication with the air conditioning control assembly. |
|
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
PROCEDURE
1. |
CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL ASSEMBLY - POWER SOURCE CIRCUIT) |
(a) Disconnect the A33 air conditioning control assembly connector.
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection |
Switch Condition |
Specified Condition |
---|---|---|
A33-8 (IG+) - Body ground |
Ignition switch off |
Below 1 V |
A33-8 (IG+) - Body ground |
Ignition switch ON |
11 to 14 V |
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection |
Condition |
Specified Condition |
---|---|---|
A33-1 (GND) - Body ground |
Always |
Below 1 Ω |
NG |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
2. |
CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY) |
(a) Disconnect the A33 air conditioning control assembly connector.
(b) Disconnect the A36 air conditioning amplifier assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection |
Condition |
Specified Condition |
---|---|---|
A33-2 (STX) - A36-11 (LIN1) |
Always |
Below 1 Ω |
A33-2 (STX) or A36-11 (LIN1) - Body ground |
Always |
10 kΩ or higher |
NG |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
3. |
REPLACE AIR CONDITIONING CONTROL ASSEMBLY |
(a) Replace the air conditioning control assembly (See page ).
HINT:
Since the air conditioning control assembly cannot be inspected while it is removed from the vehicle, replace the air conditioning control assembly with a new or known good one and same problem occurs again.
OK:
Same problem does not occurs.
Result |
Proceed to |
---|---|
OK |
A |
NG (When troubleshooting according to Problem Symptoms Table) |
B |
NG (When troubleshooting according to the DTC) |
C |
A |
END (AIR CONDITIONING CONTROL ASSEMBLY WAS DEFECTIVE) |
B |
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
C |
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY |
Outer Mirror Switch
Inspection
INSPECTION
PROCEDURE
1. INSPECT OUTER MIRROR SWITCH ASSEMBLY
(a) Check the mirror select switch and mirror surface adjust switch.
(1) Turn the mirror select switch to the L position.
Text in Illustration
*a
Mirror Select and Surfac ...
Blower Motor Controller
Components
COMPONENTS
ILLUSTRATION
Removal
REMOVAL
PROCEDURE
1. REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY
(See page )
2. REMOVE INSTRUMENT LOWER PANEL ASSEMBLY
3. REMOVE ECM (for 2TR-FE)
(See page )
4. REMOVE ECM (for 2GR-FKS)
(See page )
5. REMOVE BLOWER MOTOR ...
Transponder Key Amplifier
Components
COMPONENTS
ILLUSTRATION
Installation
INSTALLATION
PROCEDURE
1. INSTALL TRANSPONDER KEY COIL
(a) Engage the 2 claws to install the transponder key coil.
(b) Connect the connector.
2. INSTALL UPPER STEERING COLUMN COVER
(S ...