Toyota Tacoma (2015-2018) Service Manual: Outer Mirror Switch
Inspection
INSPECTION
PROCEDURE
1. INSPECT OUTER MIRROR SWITCH ASSEMBLY
(a) Check the mirror select switch and mirror surface adjust switch.
|
(1) Turn the mirror select switch to the L position. Text in Illustration
|
|
(2) Measure the resistance according to the value(s) in the table below.
Standard Resistance (for left side):
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
10 (VL) - 7 (B) 13 (M+) - 15 (E) |
Up |
Below 1 Ω |
|
Off |
10 kΩ or higher |
|
|
10 (VL) - 15 (E) 13 (M+) - 7 (B) |
Down |
Below 1 Ω |
|
Off |
10 kΩ or higher |
|
|
9 (HL) - 7 (B) 13 (M+) - 15 (E) |
Left |
Below 1 Ω |
|
Off |
10 kΩ or higher |
|
|
9 (HL) - 15 (E) 13 (M+) - 7 (B) |
Right |
Below 1 Ω |
|
Off |
10 kΩ or higher |
(3) Turn the mirror select switch to the R position.
(4) Measure the resistance according to the value(s) in the table below.
Standard Resistance (for right side):
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
12 (VR) - 7 (B) 13 (M+) - 15 (E) |
Up |
Below 1 Ω |
|
Off |
10 kΩ or higher |
|
|
12 (VR) - 15 (E) 13 (M+) - 7 (B) |
Down |
Below 1 Ω |
|
Off |
10 kΩ or higher |
|
|
11 (HR) - 7 (B) 13 (M+) - 15 (E) |
Left |
Below 1 Ω |
|
Off |
10 kΩ or higher |
|
|
11 (HR) - 15 (E) 13 (M+) - 7 (B) |
Right |
Below 1 Ω |
|
Off |
10 kΩ or higher |
If the result is not as specified, replace the outer mirror switch assembly.
(b) Check the switch illumination.
(1) Apply battery voltage between the terminals of the light and check the operation of the light.
OK:
|
Measurement Connection |
Specified Condition |
|---|---|
|
Battery positive (+) → Terminal 8 (ILL+) |
Light comes on |
|
Battery negative (-) → Terminal 14 (ILL-) |
If the result is not as specified, replace the outer mirror switch assembly.
Inner Rear View Mirror
Components
COMPONENTS
ILLUSTRATION
ILLUSTRATION
Calibration
CALIBRATION
1. SELECT COMPASS DISPLAY MODE
(a) The compass switch allows you to select the Display or Non-display mode of
t ...
Other materials:
Door Control Transmitter(w/ Smart Key System)
Components
COMPONENTS
ILLUSTRATION
Removal
REMOVAL
PROCEDURE
1. REMOVE TRANSMITTER BATTERY
Inspection
INSPECTION
PROCEDURE
1. INSPECT ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY
(a) Inspect the operation of the electrical key transmitter sub-assembly.
(1) Remove the transmitter ba ...
Unusual Bank Angle Detected (C1440)
DESCRIPTION
If the skid control ECU (brake actuator assembly) determines that the vehicle
is being driven at a steep bank angle, the skid control ECU (brake actuator assembly)
stores DTC C1440 while VSC operation is temporarily disabled.
This is not a malfunction if the system and sensor circu ...
Removal
REMOVAL
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting
the cable from the negative (-) battery terminal. Therefore, make sure to read the
disconnecting the cable from the negative (-) battery terminal notices before pr ...
