Toyota Tacoma (2015-2018) Service Manual: Installation
INSTALLATION
PROCEDURE
1. INSTALL FRONT DIFFERENTIAL CARRIER ASSEMBLY
.png)
(a) Connect the actuator hose and connector.
(b) Install the No. 1 mounting support with the 3 bolts.
Torque:
186 N·m {1899 kgf·cm, 138 ft·lbf}
(c) Install the No. 2 mounting support with the 2 bolts.
Torque:
160 N·m {1631 kgf·cm, 118 ft·lbf}
(d) Install the No. 3 front differential support with the 2 bolts.
Torque:
108 N·m {1100 kgf·cm, 80 ft·lbf}
(e) Support the front differential with a jack.
(f) Install the bolt and connect the bracket
(g) Connect the differential oil temperature sensor connector and clip.
(h) Install the 2 front mounting bolts and nuts.
for TMMTX Made:
129 N*m (1310 kgf*cm, 95 ft*lbf)
Except TMMTX Made:
137 N*m (1400 kgf*cm, 101 ft*lbf)
(i) Install the No. 1 front differential mount nut.
for TMMTX Made:
82 N*m (831 kgf*cm, 60 ft*lbf)
Except TMMTX Made:
87 N*m (889 kgf*cm, 64 ft*lbf)
(j) Install the front differential breather tube bracket with the bolt.
Torque:
13 N·m {129 kgf·cm, 8 ft·lbf}
(k) Lower the jack.
2. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH
Click here .gif)
3. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
4. INSTALL FRONT SUSPENSION LOWER ARM LH
Click here
5. INSTALL FRONT SUSPENSION LOWER ARM RH
HINT:
Use the same procedure as for the LH side.
6. INSTALL TIE ROD END SUB-ASSEMBLY LH
Click here
7. INSTALL TIE ROD END SUB-ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
8. INSTALL FRONT SPEED SENSOR LH
Click here
9. INSTALL FRONT SPEED SENSOR RH
HINT:
Use the same procedure as for the LH side.
10. INSTALL FRONT STABILIZER LINK ASSEMBLY LH
Click here
11. INSTALL FRONT STABILIZER LINK ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
12. INSTALL FRONT AXLE SHAFT LH NUT
Click here
13. INSTALL FRONT AXLE SHAFT RH NUT
HINT:
Use the same procedure as for the LH side.
14. INSTALL FRONT PROPELLER SHAFT ASSEMBLY
Click here
15. ADD DIFFERENTIAL OIL
Click here
16. INSPECT DIFFERENTIAL OIL
Click here
17. INSPECT DIFFERENTIAL OIL LEAK
18. INSTALL NO. 2 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Off Road Package)
Torque:
30 N·m {306 kgf·cm, 22 ft·lbf}
19. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
Torque:
30 N·m {306 kgf·cm, 22 ft·lbf}
20. INSTALL FRONT WHEELS
Torque:
113 N·m {1152 kgf·cm, 83 ft·lbf}
21. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
Click here
22. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
Torque:
5.4 N·m {55 kgf·cm, 48 in·lbf}
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click here
23. CHECK VSC SENSOR SIGNAL (for Hydraulic Brake Booster)
Click here
24. CHECK VSC SENSOR SIGNAL (for Vacuum Brake Booster)
Click here
Removal
REMOVAL
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting
the cable from the negative (-) battery terminal. Therefore, make ...
Drive Shaft
...
Other materials:
Removal
REMOVAL
CAUTION / NOTICE / HINT
CAUTION:
Some of these service operations affect the SRS airbag system. Read
the precautionary notices concerning the SRS airbag system before servicing
(See page ).
If the side airbag was deployed, replace the front seat assembly with
a ne ...
Removal
REMOVAL
PROCEDURE
1. REMOVE NO. 2 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Off Road Package)
2. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
3. DRAIN ENGINE COOLANT
4. REMOVE RADIATOR GRILLE
(See page )
5. REMOVE V-BANK COVER SUB-ASSEMBLY
6. REMOVE RADIATOR SUPPORT TO FRAME SEAL
7. R ...
Customize Parameters
CUSTOMIZE PARAMETERS
1. CUSTOMIZING FUNCTION WITH TECHSTREAM
NOTICE:
When the customer requests a change in a function, first make sure that
the function can be customized.
Be sure to make a note of the current settings before customizing.
When troubleshooting a function, f ...
