REASSEMBLY
CAUTION / NOTICE / HINT
HINT:
Item |
Temperature |
---|---|
Front Fender Wheel Opening Moulding or Quarter Panel Wheel Opening Moulding |
20 to 30°C (68 to 86°F) |
NOTICE:
Do not heat the front fender wheel opening moulding or quarter panel wheel opening moulding excessively.
PROCEDURE
1. INSTALL NO. 1 BODY OUTSIDE MOULDING PAD
(a) Clean the quarter panel wheel opening moulding.
(1) Using a heat light, heat the quarter panel wheel opening moulding surface.
(2) Remove the double-sided tape from the quarter panel wheel opening moulding.
(3) Clean off any tape adhesive residue with cleaner.
(b) Install a new No. 1 body outside moulding pad.
(1) Using a heat light, heat the quarter panel wheel opening moulding.
(2) Remove the release paper from the No. 1 body outside moulding pad.
HINT:
After removing the release paper, keep the exposed adhesive free from foreign matter.
(3) Install the No. 1 body outside moulding pad as shown in the illustration. HINT: Make sure to install the No. 1 body outside moulding pad so that the ends of the No. 1 body outside moulding pad are within each area shown in the illustration. |
|
2. INSTALL NO. 2 BODY OUTSIDE MOULDING PAD
(a) Clean the quarter panel wheel opening moulding.
(1) Using a heat light, heat the quarter panel wheel opening moulding surface.
(2) Remove the double-sided tape from the quarter panel wheel opening moulding.
(3) Clean off any tape adhesive residue with cleaner.
(b) Install a new No. 2 body outside moulding pad.
(1) Using a heat light, heat the quarter panel wheel opening moulding.
(2) Remove the release paper from the No. 2 body outside moulding pad.
HINT:
After removing the release paper, keep the exposed adhesive free from foreign matter.
(3) Install the No. 2 body outside moulding pad as shown in the illustration. HINT: Make sure to install the No. 2 body outside moulding pad so that the ends of the No. 2 body outside moulding pad are within each area shown in the illustration. |
|
3. INSTALL NO. 3 BODY OUTSIDE MOULDING PAD
(a) Clean the quarter panel wheel opening moulding.
(1) Using a heat light, heat the quarter panel wheel opening moulding surface.
(2) Remove the double-sided tape from the quarter panel wheel opening moulding.
(3) Clean off any tape adhesive residue with cleaner.
(b) Install a new No. 3 body outside moulding pad.
(1) Using a heat light, heat the quarter panel wheel opening moulding.
(2) Remove the release paper from the No. 3 body outside moulding pad.
HINT:
After removing the release paper, keep the exposed adhesive free from foreign matter.
(3) Install the No. 3 body outside moulding pad as shown in the illustration. Standard Measurement:
|
|
4. INSTALL FRONT WHEEL OPENING EXTENSION PAD
(a) Clean the front fender wheel opening moulding.
(1) Using a heat light, heat the front fender wheel opening moulding surface.
(2) Remove the double-sided tape from the front fender wheel opening moulding.
(3) Clean off any tape adhesive residue with cleaner.
(b) Install a new front wheel opening extension pad.
(1) Using a heat light, heat the front fender wheel opening moulding.
(2) Remove the release paper from the front wheel opening extension pad.
HINT:
After removing the release paper, keep the exposed adhesive free from foreign matter.
(3) Install the front wheel opening extension pad as shown in the illustration. HINT: Make sure to install the front wheel opening extension pad so that the ends of the front wheel opening extension pad are within each area shown in the illustration. Standard Measurement:
|
|
5. INSTALL NO. 1 FRONT WHEEL OPENING EXTENSION PAD
(a) Clean the front fender wheel opening moulding.
(1) Using a heat light, heat the front fender wheel opening moulding surface.
(2) Remove the double-sided tape from the front fender wheel opening moulding.
(3) Clean off any tape adhesive residue with cleaner.
(b) Install a new No. 1 front wheel opening extension pad.
(1) Using a heat light, heat the front fender wheel opening moulding.
(2) Remove the release paper from the No. 1 front wheel opening extension pad.
HINT:
After removing the release paper, keep the exposed adhesive free from foreign matter.
(3) Install the No. 1 front wheel opening extension pad as shown in the illustration. Standard Measurement:
|
|
6. INSTALL NO. 2 FRONT WHEEL OPENING EXTENSION PAD
(a) Clean the front fender wheel opening moulding.
(1) Using a heat light, heat the front fender wheel opening moulding surface.
(2) Remove the double-sided tape from the front fender wheel opening moulding.
(3) Clean off any tape adhesive residue with cleaner.
(b) Install a new No. 2 front wheel opening extension pad.
(1) Using a heat light, heat the front fender wheel opening moulding.
(2) Remove the release paper from the No. 2 front wheel opening extension pad.
HINT:
After removing the release paper, keep the exposed adhesive free from foreign matter.
(3) Install the No. 2 front wheel opening extension pad as shown in the illustration. Standard Measurement:
|
|
Disassembly
DISASSEMBLY
PROCEDURE
1. REMOVE RADIATOR DRAIN COCK PLUG
(a) Remove the radiator drain cock plug from the radiator assembly.
(b) Remove the O-ring from the radiator drain cock plug.
2. REMOVE RADIATOR TO SUPPORT SEAL
(a) Remove the 2 radiator to support seals from the radiator assem ...
Removal
REMOVAL
PROCEDURE
1. REMOVE FRONT CONSOLE BOX
(See page )
2. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
3. REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY
(a) Remove the nut and clip and disconnect the transmission control cable
assembly from the automatic transmission assem ...
Rear Seat Inner Belt Assembly(for Double Cab)
Installation
INSTALLATION
PROCEDURE
1. INSTALL REAR SEAT INNER BELT ASSEMBLY
(a) for LH Side:
(1) Install the rear seat inner belt assembly with the bolt.
Text in Illustration
*a
Protruding Part
*b
...