Toyota Tacoma (2015-2018) Service Manual: Engine Immobiliser System Circuit Short to Battery (B279A12)

Toyota Tacoma (2015-2018) Service Manual / Engine Immobiliser / Engine Immobiliser System(w/ Smart Key System) / Engine Immobiliser System Circuit Short to Battery (B279A12)

DESCRIPTION

When the communication line (IMI - EFIO) between the ECM and certification ECU (smart key ECU assembly) is stuck high, the ECM stores this DTC.

DTC Code	DTC Detection Condition	Trouble Area	DTC Output Confirmation Operation
B279A12	The communication line (IMI - EFIO) between the ECM and certification ECU (smart key ECU assembly) is stuck high (1 trip detection logic*1).	Wire harness or connector (disconnection or break in wire harness is main cause) Certification ECU (smart key ECU assembly) ECM	Turn the engine switch on (IG) and wait 6 seconds.

*1: Only output while a malfunction is present.

Vehicle Condition and Fail-safe Operation when Malfunction Detected

Vehicle Condition when Malfunction Detected	Fail-safe Operation when Malfunction Detected
Engine cannot be started (initial ignition occurs and engine cranks, then ignition stops)	Engine cannot be started

Related Data List and Active Test

DTC Code	Data List and Active Test
B279A12	-

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

When replacing the certification ECU (smart key ECU assembly), refer to Registration (See page ).
After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.

HINT:

When DTC B279A12 and the certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.

PROCEDURE

CLEAR DTC

(a) Clear the DTCs (See page ).

2.	CHECK FOR DTC

(a) Turn the engine switch on (IG) and wait 10 seconds.

(b) Check for DTCs (See page Result ).

Result

Result	Proceed to
DTC or B279A12 is output	A
DTC or B279A12 and other DTCs are output	B

HINT:

If DTCs other than DTC B279A12 are output, troubleshoot those DTCs first.

GO TO DIAGNOSTIC TROUBLE CODE CHART

3.	CHECK CONNECTION OF CONNECTOR

(a) Turn the engine switch off.

(b) Check that the connectors are properly connected to the ECM and certification ECU (smart key ECU assembly).

OK:

Connectors are properly connected.

CONNECT CONNECTORS PROPERLY

4.	CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)

(a) Disconnect the C27 certification ECU (smart key ECU assembly) connector.

(b) Disconnect the E14 ECM connector.

Standard Resistance:

Tester Connection	Condition	Specified Condition
C27-6 (EFIO) - E14-8 (IMI)	Always	Below 1 Ω
C27-6 (EFIO) or E14-8 (IMI) - Body ground	Always	10 kΩ or higher

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.	REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

(a) Replace the certification ECU (smart key ECU assembly) with a new one (See page ).

6.	REGISTER RECOGNITION CODES

(a) Register the key (See page ).

7.	REGISTER ECU COMMUNICATION ID

(a) Register the ECU communication ID (See page ).

CLEAR DTC

(a) Clear the DTCs (See page ).

9.	CHECK FOR DTC

(a) Check for DTCs (See page HINT: ).

HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.

OK:

DTC B279A12 is not output.

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

REPLACE ECM

Malfunction of ID-BOX Recognition (B278D)

DESCRIPTION When the certification ECU (smart key ECU assembly) detects an input signal indicating that the vehicle is equipped with an ID code box even though the ID code box is not registered, ...

Short to GND in Immobiliser System Power Source Circuit (B278A)

DESCRIPTION When there is a short to GND in the power supply for the transponder key amplifier of the engine switch, the certification ECU (smart key ECU assembly) stores this DTC. DT ...

Other materials:

USB Audio System Recognition/Play Error
DESCRIPTION When a USB device or "iPod" is connected to the USB jack of the No. 1 stereo jack adapter assembly, it must have playable files. The device must also communicate with and be recognized by the navigation receiver assembly. This diagnosis procedure is for when a device is ...

Front Passenger Side Door ECU Communication Stop (B2322)
DESCRIPTION This DTC is stored when LIN communication between the front power window regulator motor assembly RH and main body ECU (multiplex network body ECU) stops for 10 seconds or more. DTC No. DTC Detection Condition Trouble Area B2322 ...

Inspection
INSPECTION PROCEDURE 1. INSPECT FRONT SEATBACK HEATER ASSEMBLY (a) Check the operation of the front seatback heater assembly. (1) Apply battery voltage and check the operation of the front seatback heater assembly. OK: Connection Conditio ...