Toyota Tacoma manuals

Toyota Tacoma 2015-2018 Service Manual: XM Tuner Antenna Disconnected (B15FE,B15FF)

DESCRIPTION

These DTCs are stored when a malfunction occurs in the antenna assembly with holder which is connected to the navigation receiver assembly assembly.

DTC No.

DTC Detection Condition

Trouble Area

B15FE

The antenna assembly with holder is not connected.

  • Antenna cord sub-assembly
  • No. 2 antenna cord sub-assembly
  • Antenna assembly with holder
  • Stereo component tuner assembly

B15FF

A short occurs in the antenna assembly with assembly

CAUTION / NOTICE / HINT

NOTICE:

After replacing the stereo component tuner assembly of vehicles subscribed to pay-type satellite radio broadcasts, XM radio ID registration is necessary.

PROCEDURE

1.

REPLACE ANTENNA CORD SUB-ASSEMBLY

(a) Replace the antenna cord sub-assembly with a known good one and check if the same DTC is output again (See page (1) Clear the DTCs (See page  ). ).

(1) Clear the DTCs (See page (2) Recheck for DTCs and check if the same DTC is output again. ).

(2) Recheck for DTCs and check if the same DTC is output again.

OK:

No DTCs are output.

OK

END

NG

2.

REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY

(a) Replace the No. 2 antenna cord sub-assembly with a known good one and check if the same DTC is output again (See page (1) Clear the DTCs (See page  ). ).

(1) Clear the DTCs (See page (2) Recheck for DTCs and check if the same DTC is output again. ).

(2) Recheck for DTCs and check if the same DTC is output again.

OK:

No DTCs are output.

OK

END

NG

3.

REPLACE ANTENNA ASSEMBLY WITH HOLDER

(a) Replace the antenna assembly with holder with a known good one and check if the same DTC is output again (See page (1) Clear the DTCs (See page  ). ).

(1) Clear the DTCs (See page (2) Recheck for DTCs and check if the same DTC is output again. ).

(2) Recheck for DTCs and check if the same DTC is output again.

OK:

No DTCs are output.

OK

END

NG

REPLACE STEREO COMPONENT TUNER ASSEMBLY

Certification ECU Vehicle Information Reading/Writing Process Malfunction (B15F7)
DESCRIPTION This DTC is stored when items controlled by the certification ECU (smart key ECU assembly) cannot be customized via the navigation system vehicle customization screen. HINT: The cer ...

Speaker Output Short (B15C3)
DESCRIPTION This DTC is stored when a malfunction occurs in the speakers. DTC No. DTC Detection Condition Trouble Area B15C3 A short is d ...

Other materials:

Automatic High Beam System does not Operate or Operation Indicator does not Illuminate
DESCRIPTION The main body ECU (multiplex network body ECU) controls the automatic high beam system based on signals received from the forward recognition camera. WIRING DIAGRAM CAUTION / NOTICE / HINT NOTICE: When replacing the combination meter assembly, always replace it with ...

Disassembly
DISASSEMBLY PROCEDURE 1. REMOVE NO. 1 HEATER TO REGISTER DUCT (a) Remove the 2 screws <F> and screw <D>. (b) Disengage the 2 guides to remove the No. 1 heater to register duct. 2. REMOVE NO. 3 HEATER TO REGISTER DUCT ...

Acceleration Sensor Stuck Malfunction (C1232,C1243,C1245,C1279)
DESCRIPTION The skid control ECU (master cylinder solenoid) receives signals from the yaw rate and acceleration (airbag sensor assembly) via the CAN communication system. The airbag sensor assembly has a built-in yaw rate and acceleration sensor and detects the vehicle's condition using 2 ...

В© 2011-2022 Copyright www.ttguide.net