Toyota Tacoma (2015-2018) Service Manual: Installation

Toyota Tacoma (2015-2018) Service Manual / Exterior / Wheel Opening Moulding / Installation

INSTALLATION

CAUTION / NOTICE / HINT

HINT:

Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
When installing a new front fender wheel opening moulding or quarter panel wheel opening moulding, heat the vehicle body and front fender wheel opening moulding or quarter panel wheel opening moulding using a heat light.

Heating Temperature

Item	Temperature
Vehicle Body	40 to 60°C (104 to 140°F)
Front Fender Wheel Opening Moulding or Quarter Panel Wheel Opening Moulding	20 to 30°C (68 to 86°F)

NOTICE:

Do not heat the vehicle body or front fender wheel opening moulding or quarter panel wheel opening moulding excessively.

PROCEDURE

1. INSTALL FRONT FENDER WHEEL OPENING MOULDING (w/ Mudguard)

(a) Clean the vehicle body surface.

(1) Using a heat light, heat the vehicle body surface.

(2) Remove the double-sided tape from the vehicle body.

(3) Wipe off any tape adhesive residue with cleaner.

(b) Install the front fender wheel opening moulding.

(1) Using a heat light, heat the vehicle body and front fender wheel opening moulding.

(2) Remove the release paper from the front fender wheel opening moulding.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.

(3) Engage the 3 claws and 9 clips to install the front fender wheel opening moulding.

(4) Install the 7 screws.

2. INSTALL FRONT FENDER WHEEL OPENING MOULDING (w/o Mudguard)

(a) Clean the vehicle body surface.

(1) Using a heat light, heat the vehicle body surface.

(2) Remove the double-sided tape from the vehicle body.

(3) Wipe off any tape adhesive residue with cleaner.

(b) Install the front fender wheel opening moulding.

(1) Using a heat light, heat the vehicle body and front fender wheel opening moulding.

(2) Remove the release paper from the front fender wheel opening moulding.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.

(3) Engage the 3 claws and 9 clips to install the front fender wheel opening moulding.

(4) Install the 4 screws.

3. INSTALL FRONT FENDER MUDGUARD (w/ Mudguard)

(See page 4. INSTALL QUARTER PANEL WHEEL OPENING MOULDING (w/ Mudguard) )

4. INSTALL QUARTER PANEL WHEEL OPENING MOULDING (w/ Mudguard)

(a) Clean the vehicle body surface.

(1) Using a heat light, heat the vehicle body surface.

(2) Remove the double-sided tape from the vehicle body.

(3) Wipe off any tape adhesive residue with cleaner.

(b) Install the quarter panel wheel opening moulding.

(1) Using a heat light, heat the vehicle body and quarter panel wheel opening moulding.

(2) Remove the release paper from the quarter panel wheel opening moulding.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.

(3) Engage the 10 clips to install the quarter panel wheel opening moulding.

(4) Install the 3 screws.

5. INSTALL QUARTER PANEL WHEEL OPENING MOULDING (w/o Mudguard)

(a) Clean the vehicle body surface.

(1) Using a heat light, heat the vehicle body surface.

(2) Remove the double-sided tape from the vehicle body.

(3) Wipe off any tape adhesive residue with cleaner.

(b) Install the quarter panel wheel opening moulding.

(1) Using a heat light, heat the vehicle body and quarter panel wheel opening moulding.

(2) Remove the release paper from the quarter panel wheel opening moulding.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.

(3) Engage the 10 clips to install the quarter panel wheel opening moulding.

(4) Install the 7 screws.

6. INSTALL REAR QUARTER PANEL MUDGUARD (w/ Mudguard)

(See page Horn )

Removal

REMOVAL CAUTION / NOTICE / HINT HINT: Use the same procedure for the RH side and LH side. The following procedure is for the LH side. When removing the front fender wheel opening mo ...

Other materials:

FCM Destination Information Uninitialized (C1AAA)
DESCRIPTION When the forward recognition camera is replaced with a new one, the new forward recognition camera attempts to store the country specification information received from the main body ECU (multiplex network body ECU). If the forward recognition camera cannot store the country speci ...

Disassembly
DISASSEMBLY PROCEDURE 1. REMOVE REAR PROPELLER SHAFT BOOT CLAMP (a) Place matchmarks on the propeller shaft and sleeve yoke. Text in Illustration *1 Rear Propeller Shaft Boot Clamp *2 Rear Sliding Shaft ...

System Diagram
SYSTEM DIAGRAM Transmitting ECU (Transmitter) Receiving ECU Signal Communication Method 4 wheel drive control ECU Skid control ECU (Brake actuator assembly) Rear differential lock status signal H ...