Toyota Tacoma (2015-2018) Service Manual: Front Camera Module Communication Stop Mode

Toyota Tacoma (2015-2018) Service Manual / Can Communication / Can Communication System / Front Camera Module Communication Stop Mode

DESCRIPTION

Detection Item	Symptom	Trouble Area
Front Camera Module Communication Stop Mode	Either Condition is met: Communication stop for "Front Camera Module" is indicated on the "Communication Bus Check" screen of the Techstream. Click here Communication system DTCs (DTCs that start with U) that correspond to "Front Camera Module Communication Stop Mode" in "DTC Combination Table" are output. Click here	Forward recognition camera CAN branch line or connector Power source circuit of forward recognition camera Forward recognition camera ground circuit Forward recognition camera

WIRING DIAGRAM

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.

NOTICE:

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Click here
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click here
Some parts must be initialized and set when replacing or removing and installing parts.
Click here
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
Click here
Inspect the fuses for circuits related to this system before performing the following procedure.

HINT:

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.

PROCEDURE

1.	CHECK FOR OPEN IN CAN BUS LINES (FORWARD RECOGNITION CAMERA CAN BRANCH LINE)

(a) Disconnect the cable from the negative (-) battery terminal.

(b) Disconnect the forward recognition camera connector.

Standard Resistance:

Tester Connection	Condition	Specified Condition
F46-5 (CA1P) - F46-11 (CA1N)	Cable disconnected from negative (-) battery terminal	54 to 69 Ω

Text in Illustration

*a	Front view of wire harness connector (to Forward Recognition Camera)

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (FORWARD RECOGNITION CAMERA)

2.	CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
F46-10 (GND) - Body ground	Cable disconnected from negative (-) battery terminal	Below 1 Ω

(b) Connect the cable to the negative (-) battery terminal.

Standard Voltage:

Tester Connection	Switch Condition	Specified Condition
F46-7 (IGB) - Body ground	Ignition switch ON	11 to 14 V

Text in Illustration

*a	Front view of wire harness connector (to Forward Recognition Camera)

REPLACE FORWARD RECOGNITION CAMERA

REPAIR OR REPLACE HARNESS OR CONNECTOR

Open in One Side of Bus 5 Branch Line

DESCRIPTION When the CAN bus main lines are normal (no open, short to ground, short to +B or short between lines) and there is an ECU or sensor on the "Communication Bus Check" screen t ...

Tire Pressure Monitor ECU Communication Stop Mode

DESCRIPTION Detection Item Symptom Trouble Area Tire Pressure Monitor ECU Communication Stop Mode Either condition is met: C ...

Other materials:

Installation
INSTALLATION PROCEDURE 1. SET NO. 1 CYLINDER TO TDC/COMPRESSION 2. INSTALL CAMSHAFT TIMING GEAR BOLT NOTICE: There are different types of camshaft timing gear bolts. Make sure to check the identification mark to determine the tightening torque. *a Identification Ma ...

Satellite Radio Broadcast cannot be Received
CAUTION / NOTICE / HINT NOTICE: Some satellite radio broadcasts require payment. A contract must be made between a satellite radio company and the user. If the contract expires, it will not be possible to listen to the broadcast. After replacing the stereo component tuner assem ...

Pressure Control Solenoid "B" Actuator Stuck Off (P07757F)
SYSTEM DESCRIPTION The ECM uses the vehicle speed signal and signals from the transmission revolution sensors (NT, SP2) to detect the actual gear (1st, 2nd, 3rd, 4th, 5th or 6th gear). The ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical problems of t ...