Toyota Tacoma (2015-2018) Service Manual: Data List / Active Test
DATA LIST / ACTIVE TEST
1. DATA LIST
HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch ON.
(c) Turn the Techstream on.
(d) Enter the following menus:
Powertrain / Cruise Control / Data List.
(e) According to the display on the Techstream, read the Data List.
Cruise Control|
Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|
|
CCS Vehicle Spd |
Vehicle speed/min.: 0 km/h (0 mph), max.: 255 km/h (158 mph) |
Actual vehicle speed |
- |
|
CCS Mem Vehicle Spd |
Cruise control memorized speed/min.: 0 km/h (0 mph), max.: 255 km/h (158 mph) |
Actual stored vehicle speed |
- |
|
Cruise Control |
Cruise control system active condition/ON or OFF |
ON: Cruise control activated OFF: Cruise control deactivated |
- |
|
CCS Main SW M-CPU |
Main switch signal (Main CPU)/ON or OFF |
ON: Main switch on (Pushed on) OFF: Main switch off (Pushed off) |
"3" |
|
CCS Ready M-CPU |
Cruise control system standby condition (Main CPU)/ON or OFF |
ON/OFF: Change ON/OFF each time Main SW is pushed in. |
"1" |
|
CCS Indicator M-CPU |
Cruise indicator signal (Main CPU)/ON or OFF |
ON: "CCS READY" ON OFF: "CCS READY" OFF |
"2" |
|
Cancel Switch |
CANCEL switch signal/ON or OFF |
ON: CANCEL switch on OFF: CANCEL switch off |
- |
|
SET/COAST Switch |
-/SET switch signal/ON or OFF |
ON: -/SET switch on OFF: -/SET switch off |
- |
|
RES/ACC Switch |
+/RES switch signal/ON or OFF |
ON: +/RES switch on OFF: +/RES switch off |
- |
|
Stop Light SW M-CPU |
Stop light switch signal (Main CPU)/ON or OFF |
ON: Brake pedal depressed OFF: Brake pedal released |
- |
|
Cruise Operation Status |
PNP switch signal (D position)/ON or OFF |
ON: Shift lever in D OFF: Shift lever not in D |
- |
|
CCS Request Torque |
Cruise control request torque/min.: -1024 Nm, max.: 1016 Nm |
Actual required torque |
- |
|
# Codes |
Number of present trouble codes/min.: 0, max.: 255 |
Number of DTCs will be displayed |
- |
HINT:
- "3" is OK but "1" is NG → ECM failure
- "1" is OK but "2" is NG → DTC output or ECM failure
- "3" is OK but CRUISE indicator does not come on → CRUISE main indicator, wire harness or ECM failure
Terminals Of Ecu
TERMINALS OF ECU
1. ECM
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
E14-20 (TC) - ...
Diagnostic Trouble Code Chart
DIAGNOSTIC TROUBLE CODE CHART
If a trouble code is indicated while checking DTCs, inspect the circuit listed
for that code in the table below, and proceed to the applicable page.
Cruise Control Sy ...
Other materials:
Communication Error from VSC to ECM (P1630)
DESCRIPTION
The skid control ECU (brake actuator assembly) sends signals such as cruise control
cancel signals and brake demand response signals to the ECM when the dynamic radar
cruise control system is operating.
DTC No.
Detection Item
DTC Detection Condition ...
System Description
SYSTEM DESCRIPTION
1. SYSTEM DESCRIPTION
(a) The Electronic Controlled Automatic Transmission (ECT) is an automatic transmission
that has its shift timing electronically controlled by the ECM. The ECM detects
electrical signals that indicate engine and driving conditions, and controls the
sh ...
Installation
INSTALLATION
CAUTION / NOTICE / HINT
HINT:
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
PROCEDURE
1. INSTALL FRONT NO. 1 SPEAKER ASSEMBLY
(a) Install the front No. 1 speaker assembly with the 4 screws.
NOTICE:
Do not touch t ...
