TTGuideTacoma manuals & technical reference
Toyota Tacoma (2015-2018) Service Manual / Cruise Control / Dynamic Radar Cruise Control System(for 2gr-fks) / Communication Error from ECM to VSC Invalid Serial Data Received (P163181)

Toyota Tacoma (2015-2018) Service Manual: Communication Error from ECM to VSC Invalid Serial Data Received (P163181)

DESCRIPTION

The ECM sends signals such as dynamic radar cruise control operation signals, brake operation demand signals and buzzer operation demand signals to the skid control ECU (master cylinder solenoid)*1 or skid control ECU (brake actuator assembly)*2 when the dynamic radar cruise control is operating. Therefore, if the skid control ECU (master cylinder solenoid)*1 or skid control ECU (brake actuator assembly)*2 detects a communication error with the ECM, it sends a malfunction signal back to the ECM.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

P163181

Communication Error from ECM to VSC Invalid Serial Data Received

While the ignition switch is ON and the dynamic radar cruise control system is operating, the ECM continuously receives a logic error signal from the skid control ECU (master cylinder solenoid)*1 or skid control ECU (brake actuator assembly)*2 for approximately 1 second or more.
  • Vehicle stability control system
  • ECM

Does not come on
  • *1: for Hydraulic Brake Booster
  • *2: for Vacuum Brake Booster

CAUTION / NOTICE / HINT

NOTICE:

  • First check the CAN communication system by following How to Proceed with Troubleshooting. After checking that there are no malfunctions in the CAN communication system, proceed with troubleshooting.

    Click here

  • Before replacing the ECM, refer to Registration.

    w/o Smart Key System: w/ Smart Key System:

    w/ Smart Key System:

PROCEDURE

1.

CHECK FOR DTCs (VEHICLE STABILITY CONTROL SYSTEM)

(a) Check for DTCs.

  • for Hydraulic Brake Booster

    Click here

  • for Vacuum Brake Booster

    Click here

Result

Proceed to

DTCs are not output

A

DTCs are output (for Hydraulic Brake Booster)

B

DTCs are output (for Vacuum Brake Booster)

C
B

GO TO VEHICLE STABILITY CONTROL SYSTEM

C

GO TO VEHICLE STABILITY CONTROL SYSTEM

A

2.

CHECK FOR DTCs (CRUISE CONTROL SYSTEM)

(a) Clear the DTCs.

Click here (b) Perform the following procedure.

(b) Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

  1. Turn the ignition switch to ON.
  2. Turn the dynamic radar cruise control system on using the cruise control main switch.
  3. Wait for 1 second or more.

(c) Check for DTCs.

Click here

Result

Proceed to

DTC P163181 is not output

A

DTC P163181 is output

B
A

USE SIMULATION METHOD TO CHECK

B

REPLACE ECM

    Related Tacoma materials

    Components
    COMPONENTS ILLUSTRATION ILLUSTRATION ILLUSTRATION ILLUSTRATION ILLUSTRATION *A w/ Seat Heater System - - *1 FRONT SEAT CUSHION HEATER ASSEMBLY *2 FRONT SEATBACK HEATER ASSEMBLY ...

    Slip Indicator Light does not Come ON
    DESCRIPTION Refer to Slip Indicator Light Remains ON (See page ). WIRING DIAGRAM Refer to Slip Indicator Light Remains ON (See page ). CAUTION / NOTICE / HINT NOTICE: When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system informatio ...

    Daytime Running Light Relay
    Inspection INSPECTION PROCEDURE 1. INSPECT NO. 1 DAY TIME RUNNING LIGHT RELAY (a) Check the resistance. (1) Measure the resistance according to the value(s) in the table below. Standard: Tester Connection Condition Specified ...