Toyota Tacoma manuals

Toyota Tacoma (2015-2018) Service Manual: XM Tuner Antenna Disconnected (B15FE,B15FF)

Toyota Tacoma (2015-2018) Service Manual / Audio / Video / Audio And Visual System / XM Tuner Antenna Disconnected (B15FE,B15FF)

DESCRIPTION

These DTCs are stored when a malfunction occurs in the antenna assembly with holder which is connected to the radio and display receiver assembly.

DTC No.

DTC Detection Condition

Trouble Area

B15FE

The antenna assembly with holder is not connected.

  • Antenna cord sub-assembly
  • No. 2 antenna cord sub-assembly
  • Antenna assembly with holder
  • Stereo component tuner assembly

B15FF

A short occurs in the antenna assembly with holder.

CAUTION / NOTICE / HINT

NOTICE:

After replacing the stereo component tuner assembly of vehicles subscribed to pay-type satellite radio broadcasts, XM radio ID registration is necessary.

PROCEDURE

1.

REPLACE ANTENNA CORD SUB-ASSEMBLY

(a) Replace the antenna cord sub-assembly with a known good one and check if the same DTC is output again (See page (1) Clear the DTCs (See page  ). ).

(1) Clear the DTCs (See page (2) Recheck for DTCs and check if the same DTC is output again. ).

(2) Recheck for DTCs and check if the same DTC is output again.

OK:

No DTCs are output.

OK

END

NG

2.

REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY

(a) Replace the No. 2 antenna cord sub-assembly with a known good one and check if the same DTC is output again (See page (1) Clear the DTCs (See page  ). ).

(1) Clear the DTCs (See page (2) Recheck for DTCs and check if the same DTC is output again. ).

(2) Recheck for DTCs and check if the same DTC is output again.

OK:

No DTCs are output.

OK

END

NG

3.

REPLACE ANTENNA ASSEMBLY WITH HOLDER

(a) Replace the antenna assembly with holder with a known good one and check if the same DTC is output again (See page (1) Clear the DTCs (See page  ). ).

(1) Clear the DTCs (See page (2) Recheck for DTCs and check if the same DTC is output again. ).

(2) Recheck for DTCs and check if the same DTC is output again.

OK:

No DTCs are output.

OK

END

NG

REPLACE STEREO COMPONENT TUNER ASSEMBLY

Certification ECU Vehicle Information Reading/Writing Process Malfunction (B15F7)
DESCRIPTION This DTC is stored when items controlled by the certification ECU (smart key ECU assembly) cannot be customized via the audio and visual system vehicle customization screen. HINT: T ...

Sending Malfunction (Navigation to APGS) (U0073,U0100,U0140,U0155)
DESCRIPTION These DTCs are stored when a malfunction occurs in the CAN communication circuit. DTC No. DTC Detection Condition Trouble Area U0073 ...

Other materials:

Removal
REMOVAL PROCEDURE 1. REMOVE TIMING CHAIN COVER ASSEMBLY (See page ) 2. SEPARATE NO. 2 WATER BY-PASS PIPE (for Vacuum Brake Booster) 3. REMOVE VACUUM PUMP ASSEMBLY (for Vacuum Brake Booster) 4. SET NO. 1 CYLINDER TO TDC/COMPRESSION 5. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY 6. REMO ...

Zero Point Calibration of Yaw Rate Sensor Undone (C1210,C1336)
DESCRIPTION The skid control ECU (brake actuator assembly) receives signals from the yaw rate and acceleration sensor (airbag sensor assembly) via the CAN communication system. The airbag sensor assembly has a built-in yaw rate and acceleration sensor and detects the vehicle condition. If th ...

Front Speed Sensor
Removal REMOVAL PROCEDURE 1. PRECAUTION NOTICE: After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notic ...

В© 2011-2025 Copyright www.ttguide.net