TTGuideTacoma manuals & technical reference
HomeAbout carFAQReviewLatestPopularManual indexSearchContacts
Toyota Tacoma (2015-2018) Service Manual / Engine Immobiliser

Toyota Tacoma (2015-2018) Service Manual: Engine Immobiliser

  • Certification Ecu
  • Engine Immobiliser System(w/ Smart Key System)
    1. Parts Location
    2. Precaution
    3. System Description
    4. System Diagram
    5. How To Proceed With Troubleshooting
    6. Problem Symptoms Table
    7. Registration
    8. Diagnosis System
    9. Dtc Check / Clear
    10. Terminals Of Ecu
    11. Data List / Active Test
    12. Diagnostic Trouble Code Chart
    13. Engine Immobiliser System Incorrect Assembly (B279C95)
    14. Antenna Coil Open / Short (B2784)
    15. Engine Immobiliser System Signal (Some Circuit Quantity, Reported via Serial Data) Invalid (B279986)
    16. Malfunction of ID-BOX Recognition (B278D)
    17. Engine Immobiliser System Circuit Short to Battery (B279A12)
    18. Short to GND in Immobiliser System Power Source Circuit (B278A)
    19. Security Indicator Light Does not Blink
    20. Immobiliser System does not Operate Properly
  • Engine Immobiliser System(w/o Smart Key System)
    1. Parts Location
    2. Precaution
    3. System Description
    4. System Diagram
    5. How To Proceed With Troubleshooting
    6. Problem Symptoms Table
    7. Registration
    8. Diagnosis System
    9. Dtc Check / Clear
    10. Data List / Active Test
    11. Diagnostic Trouble Code Chart
    12. Theft Deterrent System Communication Line High Fixation (B279A,B279A12)
    13. Theft Deterrent System Presence Detection (B279C,B279C95)
    14. Engine Immobiliser System Malfunction (B2799,B279986)
    15. Push Switch / Key Unlock Warning Switch Malfunction (B2780)
    16. Antenna Coil Open / Short (B2784)
    17. Transponder Chip Malfunction (B2793,B2794,B2797,B2798)
    18. Engine does not Start because No Initial Combustion
    19. Engine does not Start but Initial Combustion Occurs
    20. Key Cannot be Registered
    21. Security Indicator Light Does not Blink
  • Transponder Key Amplifier
  • Transponder Key Ecu
← Previous articleTonneau Cover AssemblyRemoval REMOVAL PROCEDURE 1. REMOVE TOP COVER SUB-ASSEMBLY (a) Open the cover. (b) Remove the bolt and top cover sub-assembly. 2. REMOVE REAR BODY SIDE PAN…→ Next articleCertification EcuComponents COMPONENTS ILLUSTRATION Installation INSTALLATION PROCEDURE 1. INSTALL CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (a) Install the certification …

Related Tacoma materials

Clearance Sonar Main Switch
Components COMPONENTS ILLUSTRATION Removal REMOVAL PROCEDURE 1. REMOVE INSTRUMENT PANEL LOWER CENTER FINISH PANEL (See page ) 2. ...

Terminals Of Ecm
TERMINALS OF ECM 1. CHECK ECM HINT: The standard normal voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard normal voltage for t ...

Precaution
PRECAUTION 1. PRECAUTION (a) Before starting work on the fuel system, including inspections and repairs, disconnect the cable from the negative (-) battery terminal. (b) Do not smoke or work near fire when performing work on the fuel system. (c) Keep gasoline away from rubber or leather parts. ...

TTGuide

Toyota Tacoma manuals, maintenance guides, service procedures and technical references — organized to help you find the right information faster.

Search the manual library →

Explore

  • Manual index
  • Latest materials
  • Popular materials
  • Search manuals

Tacoma resources

  • Tacoma history
  • Tacoma review
  • Frequently asked questions

Information

  • Contact us
  • Privacy Policy
© 2011-2026 www.ttguide.net. All rights reserved. Independent reference site. Not affiliated with or endorsed by Toyota Motor Corporation. Page generated in 0.0103s