DESCRIPTION
The forward recognition camera receives vehicle stability signals from the yaw rate and acceleration sensor (airbag sensor assembly). If the yaw rate and acceleration sensor (airbag sensor assembly) detects an abnormal yaw rate sensor signal or yaw rate sensor power supply voltage, it informs the forward recognition camera via CAN communication, and DTC C1AA4 or C1AA5 is stored.
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
---|---|---|---|
C1AA4 |
Yaw Rate Sensor Circuit |
After the ignition switch is turned to ON for 3 seconds or more, when the vehicle is being driven at a speed of 1 km/h or 1 mph or more, a signal from the yaw rate and acceleration sensor (airbag sensor assembly) indicating a malfunction in the yaw rate sensor is detected by the forward recognition camera for 5 seconds or more. |
|
C1AA5 |
Yaw Rate Sensor Power Supply Voltage Circuit |
After the ignition switch is turned to ON for 3 seconds or more, when the vehicle is being driven at a speed of 1 km/h or 1 mph or more, a signal from the yaw rate and acceleration sensor (airbag sensor assembly) indicating an abnormal yaw rate sensor power supply voltage signal is detected by the forward recognition camera for 5 seconds or more. |
|
CAUTION / NOTICE / HINT
NOTICE:
Click here
Click here
PROCEDURE
1. |
CHECK FOR DTCs (VEHICLE STABILITY CONTROL SYSTEM) |
HINT:
Forward recognition camera system DTC C1AA4 or C1AA5 may be stored due to a malfunction in the vehicle stability control system. Therefore, it is necessary to check for and troubleshoot vehicle stability control system DTCs first.
(a) Check for DTCs.
Click here
Click here
Result |
Proceed to |
---|---|
Vehicle stability control system DTCs are not output |
A |
Vehicle stability control system DTCs are output (for Vacuum Brake Booster) |
B |
Vehicle stability control system DTCs are output (for Hydraulic Brake Booster) |
C |
B |
GO TO VEHICLE STABILITY CONTROL SYSTEM |
C |
GO TO VEHICLE STABILITY CONTROL SYSTEM |
|
2. |
CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM) |
(a) Clear the DTCs.
Click here
(b) Make sure that the DTC detection conditions are met.
HINT:
If the conditions are not met, the system cannot detect the malfunction.
(c) Check for DTCs.
Click here
Result |
Proceed to |
---|---|
DTC C1AA4 and C1AA5 are not output |
A |
DTC C1AA4 or C1AA5 is output |
B |
A |
USE SIMULATION METHOD TO CHECK |
|
3. |
REPLACE FORWARD RECOGNITION CAMERA |
(a) Replace the forward recognition camera.
Click here
(b) Perform forward recognition camera axis adjustment.
Click here
|
4. |
CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM) |
(a) Clear the DTCs.
Click here
(b) Make sure that the DTC detection conditions are met.
HINT:
If the conditions are not met, the system cannot detect the malfunction.
(c) Check for DTCs.
Click here
Result |
Proceed to |
---|---|
DTC C1AA4 and C1AA5 are not output |
A |
DTC C1AA4 or C1AA5 is output |
B |
A |
END (FORWARD RECOGNITION CAMERA WAS DEFECTIVE) |
B |
REPLACE YAW RATE AND ACCELERATION SENSOR (AIRBAG SENSOR ASSEMBLY) |
On-vehicle Inspection
ON-VEHICLE INSPECTION
PROCEDURE
1. INSPECT CAMSHAFT TIMING GEAR BOLT
(a) Remove the camshaft timing oil control solenoid assembly (See page
).
(b) Check that the plunger strokes when the plunger in the center of
the camshaft timing gear bolt is pressed.
Standard stroke:
4 ...
Engine Switch Illumination Circuit
DESCRIPTION
The illuminated entry system controls the engine switch illumination.
WIRING DIAGRAM
PROCEDURE
1.
READ VALUE USING TECHSTREAM (POWER/ENGINE SW LIGHT)
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch to ON.
(c) Turn the Techstream ...
Confirm Vehicle Headunit Functionality
PROCEDURE
1.
CHECK CUSTOMER'S CELLULAR PHONE COMPATIBILITY
(a) Go to TIS "Bluetooth" Compatibility Portal and check if the cellular phone
is compatible.
Result
Result
Proceed to
Cellular phone is compatible
...