TEST MODE PROCEDURE
1. TEST MODE (SIGNAL CHECK MODE) PROCEDURE
HINT:
After the tire pressure warning ECU and receiver completes the signal check for each inspection item, the DTCs for systems that are determined to be normal will be cleared. The DTCs for other inspection items may not be cleared when only a certain signal is inspected.
(a) Turn the ignition switch off.
(b) Connect the Techstream to the DLC3.
(c) Turn the ignition switch to ON and the Techstream on.
(d) Enter the following menus: Chassis / Tire Pressure Monitor / Utility / Signal Check.
Text in Illustration
*a |
0.125 sec. |
*b |
ON |
*c |
OFF |
HINT:
Every time the test mode (signal check mode) DTC clear conditions are satisfied, the tire pressure warning light illuminates for 1 second. Following this, the tire pressure warning light blinks at 0.125 second intervals.
(e) Press the tire pressure warning reset switch (DTC C2198/98).
(f) Wait for 1.5 minutes with the vehicle stopped, or drive the vehicle at a speed of 50 km/h (31 mph) or more for 1 minute (DTCs C2181/81 to C2184/84).
HINT:
The tire pressure warning valve and transmitters send signals to the tire pressure warning ECU and receiver once every 1.5 minutes while the vehicle is stopped and once every minute while driving.
(g) Check that the tire pressure warning system test mode (signal check mode) DTCs are cleared.
Test Mode (Signal Check Mode) DTC |
Test Signal |
Test Mode (Signal Check Mode) DTC Clear Condition |
---|---|---|
C2181/81 to C2184/84 |
Transmitter Data |
Data is received from the relevant transmitter which has a registered ID in the tire pressure warning ECU and receiver. |
C2198/98 |
Tire Pressure Warning Reset Switch Signal |
A signal is received indicating that the tire pressure warning reset switch is pressed. |
(h) Result
HINT:
After the signal check is completed, check for test mode (signal check mode) DTCs to confirm the system status.
Condition |
Procedure |
---|---|
Test mode (signal check mode) DTCs are output |
Repair the faulty part and enter Signal Check again |
Test mode (signal check mode) DTCs are cleared |
No problem |
(i) End of test mode (signal check mode)
(1) After completing test mode (signal check mode), turn the ignition switch off and disconnect the Techstream.
(j) Test mode (signal check mode) DTCs
(1) If a trouble code is displayed during the test mode (signal check mode) DTC check, check the diagnosis procedure listed for that code. For details of each code, refer to Link below.
DTC No. |
Detection Item |
Trouble Area |
Link |
---|---|---|---|
C2181/81 |
Transmitter ID1 not received |
|
|
C2182/82 |
Transmitter ID2 not received |
|
|
C2183/83 |
Transmitter ID3 not received |
|
|
C2184/84 |
Transmitter ID4 not received |
|
|
C2198/98 |
Initialization switch error |
|
|
Lost Communication with ECM (C1437)
DESCRIPTION
The skid control ECU (brake actuator assembly) receives signals from the ECM
via the CAN communication system.
DTC No.
Detection Item
DTC Detection Condition
Trouble Area
C1437
Lost Communication with ECM
...
Key-off Operation Function Operates even if Operating Conditions are not Satisfied
DESCRIPTION
When the front doors are closed, each power window regulator motor assembly
can control its power window operation for approximately 43 seconds after
the ignition switch is turned from ON to off by receiving operation permission
signals from the main body ECU.
How ...
Center Airbag Sensor Assembly
Components
COMPONENTS
ILLUSTRATION
On-vehicle Inspection
ON-VEHICLE INSPECTION
PROCEDURE
1. INSPECT AIRBAG SENSOR ASSEMBLY (for Vehicle not Involved in Collision)
(a) Perform a diagnostic system check (See page
).
2. INSPECT AIRBAG SENSOR ASSEMBLY (for Vehicle Involved in Collision a ...