Toyota Tacoma (2015-2018) Service Manual: Lost Communication with ECM (C1437)

Toyota Tacoma (2015-2018) Service Manual / Brake Control / Dynamic Control Systems / Vehicle Stability Control System(for Vacuum Brake Booster) / Lost Communication with ECM (C1437)

DESCRIPTION

The skid control ECU (brake actuator assembly) receives signals from the ECM via the CAN communication system.

DTC No.	Detection Item	DTC Detection Condition	Trouble Area
C1437	Lost Communication with ECM	When voltage at terminal +BS is 10 to 17.4 V and vehicle speed is 15 km/h (9 mph) or more, data cannot be sent to ECM continuously for 2 seconds or more.	CAN communication system (skid control ECU to ECM) Skid control ECU (brake actuator assembly) ECM

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information (See page PROCEDURE ).

PROCEDURE

1.	CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)

(a) Using the Techstream, check for any momentary interruption in the wire harness and connector corresponding to the DTC (See page ABS/VSC/TRAC ).

ABS/VSC/TRAC

Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
EFI Communication Open	EFI communication open detection	Normal or Error	Normal	Error: Momentary interruption
EFI Communication Invalid	ECM communication invalid detection	Normal or Error	Normal	Error: Invalid

HINT:

Perform the above inspection before removing the sensor and connector.

OK:

Normal (There are no momentary interruptions.)

CHECK CAN COMMUNICATION SYSTEM

2.	RECONFIRM DTC

(a) Clear the DTCs (See page (b) Turn the ignition switch off. ).

(b) Turn the ignition switch off.

(d) Drive the vehicle at a speed of 15 km/h (9 mph) or more for 10 seconds or more.

(e) Check that no CAN communication system DTC is output (See page (f) Check if the same DTC is recorded (See page ).

(f) Check if the same DTC is recorded (See page Result Result ).

Result

Result	Proceed to
DTC C1437 is not output	A
DTC C1437 is output	B
CAN communication system DTC is output	C

USE SIMULATION METHOD TO CHECK

REPLACE BRAKE ACTUATOR ASSEMBLY

CHECK CAN COMMUNICATION SYSTEM

Yaw Rate Sensor Malfunction (C1436)

DESCRIPTION The skid control ECU (brake actuator assembly) receives signals from the yaw rate and acceleration sensor (airbag sensor assembly) via the CAN communication system. The airbag sensor ...

Steering Angle Sensor Initialization Incomplete (C1439,C1445)

DESCRIPTION The skid control ECU (brake actuator assembly) acquires steering angle sensor zero point every time the ignition switch is turned ON and the vehicle is driven at 35 km/h (22 mph) or m ...

Other materials:

Removal
REMOVAL PROCEDURE 1. REMOVE FUEL PUMP ASSEMBLY (for High Pressure) (See page ) 2. REMOVE NO. 2 FUEL PIPE SUB-ASSEMBLY (a) Loosen the 2 union nuts and remove the No. 2 fuel pipe sub-assembly from the fuel delivery pipe RH and fuel delivery pipe sub-assembly LH. Text in Illustration ...

Voice Recognition Microphone Disconnected (B1579)
DESCRIPTION The radio and display receiver assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines. This DTC is stored when a microphone connection detection signal line is disconnected. DTC Code DTC Det ...

Auxiliary boxes
Front Pull the lid down. Under the rear seats (Access Cab models) Pull up the lever. Raise the bottom cushion up. Turn the knob counterclockwise. Open the lid. Press the lid against the bottom of the lower cushion until it is supported by the hookand- loop fastener. Make sur ...